An intumescent basecoat used as part 1 of a system to achieve 30 or 60 minute fire resistance for compartmentation.
Please note that this product CANNOT be used without first receiving an application schedule from our Technical Department. Please see below.
Please note that this product CANNOT be used without first receiving an application schedule from our Technical Department. Please download and complete the 'Thermoguard Wood Enquiry Form' and return by email to [email protected]
If you have any questions regarding this process consult our technical department on 0113 2455450 (option 2).
Thermoguard Timbercoat
Part of a Fire Protection Upgrade System for bare & suitable multi-layer painted wood and wood derivatives. Part 1 of a system achieve 30 or 60 minute Fire Resistance for compartmentation. The finished system forms a smooth aesthetically pleasing, durable finish resistant to repeated cleaning to internal and external wood.
Packs containing both Thermoguard Timbercoat basecoat and SFR Topcoat can be found here: Thermoguard Timbercoat 30 & 60 Minute System.
When exposed to fire:-
Please download and complete the 'Thermoguard Wood Enquiry Form' and return by email to [email protected]
For 30 & 60 minute protection please see Thermoguard Timbercoat 30 & 60 Minute System
For fire protection to doors, see Door Upgrade Products
Please note: Timber must be clean and thoroughly dry prior to application (maximum 18% moisture content). Any gaps should be sealed with Thermoguard Intumescent Mastic. Fire should be prevented from accessing unprotected wood surfaces and for external applications it is recommended wood has been sealed on the reverse face to stop water ingress.
NOT suitable for the topside of floor surfaces that will be trafficked/walked on.
Brush & Roller;
Woven fabric roller sleeves and synthetic bristle brushes
Spray;
Pressure Pot & Gun conventional unit with small compressor: Ensure all traces of solvent flushed out. Thin 5 > 10% with water to spray viscosity. Adjust fluid flow & air flow as normal for acrylic emulsion paint OR Airless Graco 1500, 3500 or equivalent. 3/8” line, 30 mesh filter on machine, no filter in gun. 521 or 523, broad areas 621 or 623 tip. Ensure coverage is applied as per technical specification.
Once the works are complete the relevant certification can be applied for HERE
Preparation
All surfaces must be clean and dry.
Remove all possible surface contaminates such as grease, smoke residues, silicates etc.
Seal water-stain risks with stain blocking sealer suitable to overcoat with water-based acrylic paints.
Abrade hard or smooth surfaces with wetted 120 grit wet-or dry abrasive or dust extracting abrader. Rinse off slurry while still damp. When dry, remove any loose or suspect material back to firm edge.
Fill and repair any damage to the substrate using a good quality remedial filler
Application Conditions
Low Voc. Limit for this product (cat A/i) is 140 g/l. This product contains just 16 g/lv
Catalytic powder, expansion agent, char former, char hardeners & fibres Binder: Fire protection adhesive grade rapid reaction acrylic resin. Water based
Return as much unused material to its original container as possible. Wash brushes rollers and guns with clean waters immediately following use.
Please refer to the relevant Safety Data Sheet for full details of this product. Apply all products in accordance with BS 6150:2019- Code of practice for painting of buildings.
Do not store this product in cold temperatures below 5°C or above 30°C.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Raquel on 2023-09-08 21:25:28 | Question: I have bought the two-part system Thermoguard timbercoat and flame retardant topcoat. I have applied them myself following the instructions received by Rawlins technical team. When applying for the fire certificate, I have been asked for the name of the contractor that applied the paint. Would that be a problem if I applied it myself instead of a painter? |
Answer from Rawlins’ Technical Team: When filling out this question on the certificate application you will be fine to put your own details if you applied the system yourself. | |
| Baz on 2022-05-27 19:09:35 | Question: How many square metres does a 25kg tin cover. Thanks |
Answer from Rawlins’ Technical Team: This product must be used as part of a system to a achieve level of fire protection on a suitable substrate. As such the coverage rate and number of coats required can vary. Please provide the information below to [email protected] and we can assist with a specification. GENERAL TIMBER SURFACES | |
| Jack miller on 2020-03-02 22:24:19 | Question: Hi Does this need a special primer or top coat? Or is it a one coat system? |
Answer from Rawlins’ Technical Team: This is one part of a two part system and does require the appropriate topcoat. Please see Thermoguard Timbercoat BS Class 1/0 & EN Class B System or Thermoguard Timbercoat 30 & 60 Minute System. | |
| Sally on 2018-07-01 12:41:11 | Question: Can Themaguard paints be over painted with Farrow And Ball or other speciality paint? |
Answer from Rawlins’ Technical Team: Ideally Thermoguard want the topcoat of their system to remain the final finish as they can be produced in a wide range of finishes and colours (including colour matches). However, in certain instances if required Thermoguard do allow their systems to be over painted with a conventional decorative topcoat over their FULL system. Thermoguard would want their complete system applying, including their recommended topcoat in the nearest colour available and then (with their approval on your specific project) a like for like conventional topcoat can be applied - i.e. if you have used Thermoguard Smoke & Flame Retardant Dualcoat Eggshell as your finish then you use an acrylic eggshell as a finish in the conventional decorative topcoat. Prior approval must be sought for this from our Technical Department before proceeding. | |
| Karen on 2018-05-01 06:30:34 | Question: Can this product be used as a topcoat over pre painted pressurised decking already painted with sadolin decking paint |
Answer from Rawlins’ Technical Team: No, Thermoguard Timbercoat is cannot be used on floor surfaces which will receive traffic. | |
| Alan Smith on 2018-02-24 10:54:09 | Question: Can Thermoguard be applied over Dulux Weathershield paint If so are there any special precautions required |
Answer from Rawlins’ Technical Team: Thermoguard Timbercoat can be applied over existing coatings in instances where surfaces are free of contamination, sound, clean and dry. Adhesion of the existing coating has been checked and found to be adequate and the coating is not unknown or another fire coating. Thoroughly abrade knotting, gloss, hard or smooth paints to provide a key before application. If in doubt, please contact our Technical Department before use. | |
| phill clarke on 2018-02-04 17:41:05 | Question: can it be used on mdf |
Answer from Rawlins’ Technical Team: Yes, MDF has a smooth and a coarse face, if coating the smooth face thoroughly abrade to provide a suitable key before application. | |
| Brian on 2015-05-28 18:32:32 | Question: Using Thermoguard Timbercoat (3 coats plus colour top coat) how long between coats ? Spec says touch dry 4 hrs but not for between coats. |
Answer from Rawlins’ Technical Team: Touch dry time is 4 hours, overcoat time is 6 hours. Based on good drying conditions at 20°C. | |
Thermoguard Timbercoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Thermoguard Smoke & Flame Retardant (SFR) Dualcoat is for use over Thermoguard Timbercoat or Thermoguard Timbercoat Insulating Basecoat.Topcoat and maintenance paint for timber surfaces protected with Thermoguard Timbercoat Emits a safe fire-damping vapour in a fire to control flame spread and suppress smoke. As part of a complete...
£75.35 (incl. VAT)
£62.79 (ex. VAT)
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...
£12.04 (incl. VAT)
£10.03 (ex. VAT)
4,000+ coloured fire retardant paint system for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Thermoguard Timbercoat Insulating Basecoat) and topcoat (Smoke & Flame Retardant Dualcoat) to ensure protection is achieved in line with the manufacturers recommendations to the area in question....
£214.45 (incl. VAT)
£178.71 (ex. VAT)
An intumescent paint system in 4,000+ colours for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Thermoguard Smoke & Flame Retardant (SFR) Dualcoat) to ensure protection is achieved inline with the manufacturers recommendations to the respective area in question....
£208.66 (incl. VAT)
£173.88 (ex. VAT)
Thermoguard Timbercoat Door Upgrade System is an intumescent paint system to upgrade solid doors to 30min Fire Resistance.Available as a convenient pack containing the required basecoat and topcoat to protect 2 doors in a white or coloured Eggshell or Gloss finish Thermoguard UK will issue a Fire Certificate for Authority approved...
£204.79 (incl. VAT)
£170.66 (ex. VAT)
