Anglo Speed Screed
Anglo Speed Screed smooth's uneven, damaged or worn concrete floors. A pour on, durable re-surfacing material.
Rough concrete floors can be transformed rapidly and easily with this self-smoothing, hard wearing material designed to meet the demands of industrial use. Anglo Speed Screed gives a mid grey, non dusting, slip-resistant surface that requires no further treatment before use. A mixing paddle for an electric drill and a spiked roller are available for use with this product.
• Extremely durable - even withstands forklift trucks
• Can be painted with any Anglo epoxy resin coating
• Apply from 3mm to 15mm thick
• Suitable for interior or exterior use
Usage rate:
25kg covers 3.7m2 at 3mm thick
2.7m2 at 5mm thick
1.35m2 at 10mm thick
Size available: 25kg
Surface Preparation:
Concrete should be free of loose material, soft surface laitance and contaminants. New concrete must be at least four weeks old. Remove all loose material by wire brushing. General dirt etc., should be removed with a strong neutral cleaner. Oil and grease can be removed with Anglo Multi-Purpose Degreaser. Cracks in concrete should be raked out and all loose material removed.
Painted or Sealed Surfaces:
Mechanically remove as much paint or sealant as possible. Please contact our Technical Department for further advice.
Priming:
Two primers are supplied. Dampen areas of bare concrete with clean cold water and leave for 20 - 30 minutes prior to applying Primer 1. Apply Primer 1 to the prepared surface using a brush or soft broom. Apply the Primer evenly avoiding ‘ponding’ on the surface and allow it to dry. Then apply Primer 2.
Mixing (immediately after Primer 2 has been applied):
Pour the Resin into the empty Speed Screed container. Add the powder to the liquid slowly and blend in using a slow speed electric drill fitted with a paint stirrer until a completely even colour and consistency is obtained (3 to 5 minutes).
Application:
Pour the mixed components onto the wet Primer 2. Use a trowel to spread the Anglo Speed Screed across the surface of the concrete at the desired thickness (it may be convenient to work to a thin batten but this must be removed before working further sections). It is not essential that trowel marks are removed at this stage.
Immediately after application a spiked roller should be used to even out the material and release any trapped air. Use the spiked roller quite vigorously rolling each area 3 or 4 times from different directions. The spiked roller should not be used for more that 20 minutes as the Anglo Speed Screed will have started to cure and the roller may leave marks.
If it is necessary to walk on areas of wet primer whilst applying Anglo Speed Screed care should be taken not to tread wet primer or Anglo Speed Screed onto surrounding surfaces.
In exceptional temperature conditions advice should be obtained from our Technical Department.
Curing Time:
Foot and light traffic may be allowed after approximately 6 hours. The surface will be available for full use after 24-36 hours when laid at normal thickness. These guidelines assume an ambient temperature of approximately 15ºC - 20ºC and good ventilation. Lower temperatures will retard curing. Do not apply at less than 5ºC. Temperatures over 25ºC can make the material a little sticky to apply and lead to rapid drying out causing surface crazing.
The surface is inherently anti-slip in dry conditions.
Over coating:
Anglo epoxy coatings may be used to coat the surface of Anglo Speed Screed where a more decorative finish is desired. Solvent free products can be applied after 24-36 hours. Solvent based epoxy coatings should not be applied for 7 days. Anglo Epoxy Floor Paint (solvent free) provides a hard wearing, attractive surface. Anglo Safe ‘T’ Epoxy (solvent free) or Anglo Tread Safe (solvent free) offer anti-slip finishes to promote a safe working environment. We do not recommend application of Anglo Floor Paint or any paint that may be affected by the residual alkalinity of the recently laid Anglo Speed Screed.
Important:
Do not apply to surfaces where sugars or sugar solutions have been stored. Disclaimer
Please download and carefully read product datasheets before application
|
