RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments.Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...
Keim Concretal-MR 2.0 (Keim Concrete Repair Mortar) is a cementitious repair mortar designed for quick repair work to concrete surfaces. A single component, polymer modified, cement bound mortar, to be mixed with water.Density: Q = 1.3kg/lt Grain size: 0 to 2mm Fresh mortar bulk density: 2.0 kg/dm3 Compressive strength 28d: 55N/mm²...
Designed for thick section repairs, haunching reinstatements, ironwork backfilling and commerical sign/post installation.HAPAS Approved since 2005 20N/mm² compressive Rapid set: 10-20 minutes strength in 2 hours Open to traffic: 2 hours • Shrinkage compensatedMore Information Delivery Info
Sikafloor 81 EpoCem is a three part cement and epoxy combination mortar from Sikafloor for self-smoothing floor screeds of 1.5 to 3mm. Use as a Temporary Moisture Barrier (TMB) or under Epoxy, Polyurethane and PMMA resin floors, over high moisture content substrates, even green concrete. More Information Delivery Info
Fosroc Conbextra BM (Bedding Mortar) is a single component cementitious high strength bedding mortar. Suitable for use in the structural bedding in of precast modular concrete units. Conbextra Bedding Mortar is a blend of Portland cements, chemical additives and graded aggregates. More Information Delivery Info
Fosroc Conbextra EP10 is a two component epoxy resin free-flow grout conforming to the requirements of BS EN1504-3 Class R4 and BS EN1504-6 - Anchoring of reinforcing steel bar. Suitable for use on concrete and steel for grouting under baseplates, crane rails, turbines where heavy dynamic loads are encountered and areas where chemical...
Fosroc Conbextra EPR is a three component epoxy resin free-flow grout conforming to the requirements of BS EN1504-3 Class R4 and BS EN1504-6 - Anchoring of reinforcing steel bar. Suitable for use on concrete and steel for grouting under baseplates, crane rails, turbines where heavy dynamic loads are encountered and areas where chemical...
Fosroc Lokfix S25 is a two component polyester resin anchoring grout meeting the requirements of BS EN 1504-6 - Anchoring of reinforced steel bars. Suitable for use for anchoring of steel bars into concrete, brickwork, masonry and rock. Recommended applications include installation of starter bars, base plate bolts, MOT Bolts, installation...
Fosroc Conbextra HF is a high-flow, non-shrink, cementitious grout conforming to the requirements of BS EN 1504-3 Class R4 and BS EN 1504-6 - Anchoring of reinforcing steel bar. Suitable for use on concrete for grouting gap thicknesses from 10mm to 100mm. Recommended applications include large stanchion baseplates, joints between pre-cast...
Fosroc Conbextra TS is a high-flow, non-shrink, thick-section, aggregate filled cementitious grout conforming to the requirements of BS EN 1504-3 Class R4. Suitable for use on concrete for free flow grouting for gap thicknesses from 75mm to 500mm. For smaller gaps please see Fosroc Conbextra HF. Recommended applications include large...
Fosroc Conbextra PM is a single component thixotropic cementitious pumping and pointing mortar. Suitable for use for the structural grouting of gaps in precast concrete units and high strength pointing. Fosroc Conbextra PM requires only the addition of clean water to produce an easily pumped mortar. More Information Delivery Info
Fosroc Conbextra UW is a non-shrink free flow or pumped cementitious grout for underwater installation conforming to the requirements of BS EN 1504-3 Class R4. Suitable for use underwater or in tidal zones where “wash out” would be a problem with conventional grouts. Recommended applications include stanchion baseplates, bridge columns, quay...