Sub-category links
Filter By
For Use By
For Use By
Product Range
Product Range
Suitable For Use On
Suitable For Use On
Product Type
Product Type
Colour Family
Colour Family
Interior / Exterior Use
Interior / Exterior Use
Single, Two or Three Pack
Single, Two or Three Pack
Base Type
Base Type
Application Method
Application Method
Finish
Finish
Hitex lead research, development, and the manufacture of road safety markings and surfacing products, with formulations to suit contractor requirements. Their full range of road surface products are available at Rawlins Paints for lining and marking roads and highways, pathways and cycle paths, and playgrounds:
• MMA Road Marking Paints
• MMA Cycle Path and Walkway Paints
• Preformed Thermoplastic Road Markings
• Preformed Thermoplastic Speed Roundels, Symbols, Letters and Numbers, and Lines
There are 15 products.
Active filters
Pre-formed thermoplastic lines that are fast and convenient to install, with excellent adhesion, durability, flow and colour stability.Suitable for:Reinstatement of markings following utility works Fast and simple installation of new letters / numbers / symbols Small scale lining work such as car parks School playground educational...
A preformed system for the permanent repair of open seams, joints or cracks. Used as a simple overband, it will repair defects up to 5mm wide. Ideal for sealing the surface following asphalt patching such as utility works.Simple torch on application provides a simple overband seal No need for large scale application equipment – just a gas...
A preformed overband tape system for the permanent repair of open seams, joints or cracks. Used as a simple overband, it will repair defects up to 5mm wide. Overbanding tape is a long lasting, rapid solution for sealing surfaces following road repairs and utility works.Simple torch on application provides an overband seal No need for...
Pre-formed thermoplastic symbols that are fast and convenient to install, with excellent adhesion, durability, flow and colour stability. See ordering references below.Suitable for:Reinstatement of markings following utility works Fast and simple installation of new letters / numbers / symbols Small scale lining work such as car...
Pre-formed thermoplastic letters and numbers that are fast and convenient to install, with excellent adhesion, durability, flow and colour stability.Suitable for:Reinstatement of markings following utility works Fast and simple installation of new letters / numbers / symbols Small scale lining work such as car parks School...
HT Primer is a clear liquid tack coat primer designed for the adhesion of thermoplastic road markings onto bituminous and non-bituminous substrates. HT Primer is an easy to apply, low viscosity, colourless liquid tack coat primer.The use of HT Primer with Hitex thermoplastic markings is strongly recommended on any substrate that may prove...
A durable and easy to install patch kit that can be used to repair worn or damaged areas of high friction surfacing as well as ramps, paths and walkways. PumaGrip MMA provides an all in one anti skid surfacing solution with no specialist equipment required.Cold Applied MMA High Friction Surfacing Repair Kit Provides up to 2m2 of coverage...
A clear aerosol spray primer designed for the adhesion of thermoplastic road markings onto bituminous and non-bituminous substrates. HiTack Primer is an easy to apply, colourless aerosol spray tack coat primer.The use of HiTack Primer with Hitex thermoplastic markings is strongly recommended on any substrate that may prove difficult for...
A separate catalyst system to enable curing for Hitex marking products. Dosage of the catalyst varies according to material temperature.IMPORTANT - refer below for levels required when using with PumaBrite, PumaTrack, and CM PrimerMore Information Delivery Info
MMA cold plastic road marking materials, engineered to achieve the highest levels of retroreflectivity, durability, adhesion and colour stability. PumaBrite is suitable for structured (Type 2) enhanced wet night reflectivity, centre and edge line markings, junction markings, letters, arrows and other road marking symbols, smaller scale works...
Coloured MMA Road Surface Treatment. Quick and easy to install and ideal for walkways and cycle paths, PumaTrack surface treatment is engineered to achieve the highest levels of durabillity, adhesion and colour stabillity. Smooth or textured finish, depending on application.Separate hardener (Hitex BPO Powder Catalyst) required, levels...
Primer for Hitex Puma MMA systems on metal and concrete substrates (e.g. iron, aluminium, stainless steel), with excellent adhesion.Easy to apply Separate hardener (Hitex BPO Powder Catalyst) required, levels depend on substrate temperatureMore Information Delivery Info Hitex BPO Powder Catalyst
Sub-category links
Filter By
For Use By
For Use By
Product Range
Product Range
Suitable For Use On
Suitable For Use On
Product Type
Product Type
Colour Family
Colour Family
Interior / Exterior Use
Interior / Exterior Use
Single, Two or Three Pack
Single, Two or Three Pack
Base Type
Base Type
Application Method
Application Method
Finish
Finish
Hitex are the experts in Global Road Safety Solutions.
Their high-performance preformed road markings and anti-skid/high friction surfacing products help to promote road safety. Millions of vehicles are guided and controlled on the road roads every day with effective navigational guides that are simple and easily recognisable. Hitex uses the highest quality raw materials and manufacturing processes to produce road markings at the highest levels of quality in the industry. Their pre-formed thermoplastic road marking materials are manufactured in accordance with ISO 9001 and 14001 standards.
High-friction surfacing is designed to help reduce braking distances, particularly when conditions are wet, and to prevent skidding. Type 1 anti-skid surfacing has demonstrated in numerous industry studies to be a direct link in the amount of incident reductions in a wide number countries, over long periods of time. Such installations provide safer roads that save countless lives in both wet and dry conditions, not to mention the associated financial consequences, often used in:
Type 1 is the highest level of certification applied to high friction products, and Hitex epoxy Type 1 materials are accredited by the British Board of Agreement (BBA) certification scheme, covering products and approved installers and regulated in the UK under the Highways Agency BBA/HAPAS scheme.
Hitex manufactures premium quality hot and cold-applied anti-skid material that is suitable for use in a diverse range of road infrastructure projects, including:
