Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Carboline Carboguard 890 LT GF is a two-component, glass reinforced chemically resistant epoxy coating with wide versatility in all industrial markets.
Carboline Carboguard 890 LT GF is a two-component, glass reinforced chemically resistant epoxy coating with wide versatility in all industrial markets. It is self-priming. Glass reinforcement improves internal film strength, hardness, impact, and abrasion resistance. It is often used in severe service (above or below the water line) in marine applications where these resistance qualities are desired.
Technical Data | |
---|---|
Carboline Carboguard 890 LT GF | |
Primer | Normally self-priming May be applied over Carboguard 890 and other epoxy primers |
Topcoats: | May be coated with acrylics, epoxies or polyurethanes depending upon exposure and need |
Volume Solids: | By Volume 81% +/- 2% |
Theoretical Coverage Rate: | 31.9 m²/l at 25 microns 4.0 m²/l at 200 microns 1.6 m²/l at 500 microns Allow for loss in mixing and application |
Dry Film Thickness: | 203 - 508 microns per coat |
VOC Values: | As Supplied: 168 g/l Thinner 2: 13 oz/gal: 230 g/l Thinner 213: 13 oz/gal: 221 g/l Thinner 33: 16 oz/gal: 248 g/l Use Thinner 76 up to 16 oz per gallon where on-photochemically reactive solvents are required. |
Dry Temp. Resistance: | Continuous: 121°C Non-Continuous: 149°C Discolouration and loss of gloss observed above 200°F (93°C) |
Flash Point: | Part A: 32° C Part B: 23°C N/A for Glass Flake Additive Mixed: 26°C |
Shelf Life: | Part A: 36 months at 24°C Part B: 15 months at 24°C Glass Flake Additive – 60 months at 24°C |
Curing Schedule | ||||
---|---|---|---|---|
Surface Temp | Dry to Handle | Dry to Recoat and Topcoat w/ other finishes | Dry to Touch | Final Cure General |
2°C | 18 Hours | 20 Hours | 5 Hours | 7 Days |
4°C | 15.5 Hours | 16 Hours | 5 Hours | 5 Days |
10°C | 7 Hours | 12 Hours | 3.5 Hours | 3 Days |
16°C | 5 Hours | 8 Hours | 2 Hours | 2 Days |
24°C | 2 Hours | 4 Hours | 1.5 Hours | 24 Hours |
32°C | 1.5 Hours | 2 Hours | 1 Hour | 16 Hours |
General
Steel
Galvanised Steel
Concrete or CMU
Previously Painted Surfaces
Product Information | |
---|---|
Mixing: | Power mix A and B separately, then combine and power mix. Then slowly add the Glass Flake Additive and power mix for 3-5 minutes DO NOT MIX PARTIAL KITS |
Thinning: | Spray: Up to 13 oz/gal (10%) w/ Thinner 2 Brush: Up to 16 oz/gal (12%) w/ Thinner 33 Vertical Surfaces: Up to 13 oz/gal (10%) w/ Thinner 213, Thinner 2 or Thinner 33 Thinner 33 can be used for spray in hot/windy conditions. Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implie |
Ratio: | 1:1 Ratio (A to B) plus 1 bag (3.62 lbs/2 gal mix) |
Pot Life: | 2 Hours at 24°C Pot life ends when coating loses body and begins to sag. Pot life times will be less at higher temperatures |
Conventional Spray: | Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, .110” I.D. fluid tip and appropriate air cap |
Airless Spray: | Pump Ratio: 30:1 (min.) GPM Output: 3.0 (min.) Material Hose: 3/8” I.D. (min.) Tip Size: .025”-.035” Output PSI: 2200-2500 |
Brush and Roller: | Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding |
Brush: | Use a medium bristle brush for touch up and striping of welds only |
Roller: | Not recommended |
Product Conditions | |||||
---|---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity | |
Minimum | 4°C | 2°C | 2°C | 0% | |
Maximum | 32°C | 52°C | 43°C | 90% |
Clean Up
Safety
Ventilation
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Carboguard 890 LT GF is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
Carboline Thinner 33 is a thinner for use in industrial coatings. More Information Delivery Info
£42.76 (incl. VAT)
£35.63 (ex. VAT)
Carboline Thinner 213 is a thinner for use in industrial coatings. More Information Delivery Info
£48.16 (incl. VAT)
£40.13 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)