HMG Hardener 9030

    CUR9030
    HMG4516

    HMG Hardener 9030 is an isocyanate hardener.

    • Designed for use in recommended HMG Alkyd and Polyurethane Alkyd products
    • Upgrades the performance characterstics of the system

    Size
    £49.28(ex. VAT)
    £59.14 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Hardener 9030 is an isocyanate hardener.



    Click To Jump To Section:




    Features & Benefits


    • Designed for use in recommended HMG Alkyd and Polyurethane Alkyd products
    • Upgrades the performance characterstics of the system



    Mixing instructions appear on the base component.

    Mixing ratios of 10:1 or 5:1 (Base : Hardener) can be employed.



    Product Specification


    Technical Data
    HMG Hardener 9030
    Volume Solids:59.8%
    VOC Content:0.400 Kg/l
    SG:-
    Viscosity:29 mPas
    Density:1.033 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Flash Point:25°C



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Product Notes


    Information On Basic Physical And Chemical Properties
    HMG Hardener 9030
    Form:According to product specification
    Colour:According to product specification
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value 20°C:Not determined
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:126°C
    Flash Point:25°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:315°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:1.1 Vol %
    Explosion limits: Upper:10.8 Vol %
    Vapour pressure at 20°C:6.7 hPa
    Density at 20°C:1.033 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:29 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:40.0%
    Solvent content:59.8%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.

    Click to go back to the top of the page

    Product Details
    4516-705458

    Data sheet

    Manufacturer
    HMG Paints Limited
    Single, Two or Three Pack
    Single
    Mixing Ratio
    Mixing ratios of 10:1 or 5:1 (Base : Hardener) can be employed
    Density
    1.033 g/cm³
    Solids by Volume
    59.8%
    VOC
    0.400 Kg/l
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers
    Size
    1L
    UN Number
    1263
    Base Type
    Isocyanite
    Product Usage Type
    Hardener
    Categorised As
    Accessories > Hardeners & Activators
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Hardener 9030 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT