HMG C71 Speedline is a high quality, single pack, synthetic alkyd enamel suitable for brushing or spraying. Offers fast surface drying, good through drying (even in thick films), and a hard, tough finish, with minimal yellowing even at high temperature - ideal for machinery, appliance and agricultural projects. For use on ferrous and...
HMG Thinner 2612 is a slow thinner.
Click To Jump To Section:
Features & Benefits
- For use with compatible HMG systems.
Suitable for use with the following HMG products:
- HMG 14 Line Fleet Polyurethane
- HMG C71 Speedline
- HMG Coach Enamel
- HMG D66 Economy Line
- HMG Marine Varnish
- HMG SAH300 Enamel
- HMG A1242 Undercoat
- HMG KX Undercoat
- HMG Synthetic BDX Primer
- HMG Synthetic High Opacity Undercoat
- HMG Synthetic LP Primer
|HMG Thinner 2612|
|Storage Conditions:||Store between 5°C - 25°C. When not in use, cans must be kept sealed.|
|Shelf Life:||12 months from delivery date in original sealed containers.|
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
|Information On Basic Physical And Chemical Properties|
|HMG Thinner 2612|
|Form:||According to product specification|
|Colour:||According to product specification|
|Odour Threshold:||Not determined|
|pH-value 20°C:||Not determined|
|Melting point/freezing point:||Undetermined|
|Initial boiling point and boiling range:||135°C|
|Flammability (solid, gas):||Not applicable|
|Decomposition temperature:||Not determined.|
|Auto-ignition temperature:||Product is not selfigniting.|
|Explosive properties:||"Product is not explosive. However, formation of explosive air vapour mixtures are possible."|
|Explosion limits: Lower:||0.6 Vol %|
|Explosion limits: Upper:||7 Vol %|
|Vapour pressure at 20°C:||Not determined|
|Density at 20°C:||0.78g/cm³|
|Relative density:||Not determined|
|Vapour density:||Not determined|
|Evaporation rate:||Not determined|
|Solubility in / Miscibility with water:||Fully miscible|
|Partition coefficient: n-octanol/water:||Not determined|
|Viscosity: Dynamic at 20°C:||2 mPas|
|Viscosity: Kinematic:||Not determined|
|Solvent content: Organic solvents:||100.0%|
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- HMG Paints Limited
- 0.78 g/cm³
- Solids by Volume
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- 1L, 5L & 25L
- UN Number
- Product Type
- Product Range
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Thinner 2612 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Coach Enamel is traditional, ultra high quality, high build, long oil synthetic enamel for brush application. It gives an extra long wet edge time allowing it to be brushed without brush drag. High gloss Excellent water resistance Flexible with good exterior durability and toughness Available in 3,500 colours from RAL, NCS, and...
HMG D66 Economy Line is an alkyd based synthetic enamel designed for general purpose brush and spray requirements. It is also oil and diesel resistant making it a good choice for agricultural, appliance & machinery finishes. Good performance Oil and diesel resistant Quick drying agricultural paint Quick drying appliance paint...
HMG SAH300 Enamel is a high solids, gloss 1K polyurethane alkyd designed for brush application. Excellent protection against harsh weather conditions, atmospheric pollution, road dirt, sharp cleaning agents and mechanical car washes etc Available in 5,000+ colours from RAL, NCS, and British Standard Also available as an aerosol, please...
HMG Marine Varnish is a tough and durable clear gloss formulated on a unique blend of polyurethane alkyds for high quality marine and can be used for industrial finishing. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner: 2-Pack System Details Base (Part 1) HMG...
HMG 14 Line Fleet Polyurethane is a high build, high solids polyurethane based on a unique blend of polyurethane alkyds. It combines a long wet edge time with excellent hot spray application offering superb durability and gloss retention. Can be brushed directly from the can or with the addition of a small amount of thinner Suitable for...
HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties. For use on suitably prepared structural steel, chassis, fabrication and aluminium Can be applied to bare...
HMG Synthetic LP Primer is a high build, anti-corrosive, 1K alkyd primer for use under all HMG synthetic topcoats. It combines high build and after a suitable drying period exhibits excellent application and scratch filling properties. More Information Delivery Info
HMG KX Undercoat is a high build polyurethane alkyd undercoat. Offers excellent wet edge characteristics and superb topcoat holdout Formulated for use under all HMG Synthetic topcoats Available in 5,000+ colours from RAL, NCS, and British Standard Also available as an aerosol, please see HMG KX Undercoat Aerosol Please note: Colours...
HMG Synthetic High Opacity Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties. Suitable for large areas due to its ease of application and long wet edge time Please note: Colours shown are for illustrative purposes only More Information Delivery Info
HMG A1242 Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties. Suitable for large areas due to its ease of application and long wet edge time. Coverage Calculator More Information Delivery Info