HMG PVC Pro Colours Aerosol is specifically developed to adhere to uPVC substrates to renovate window frames, conservatories and doors. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG PVC Pro Colours.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG PVC Pro Colours Aerosol is specifically developed to adhere to uPVC substrates to renovate window frames, conservatories and doors. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG PVC Pro Colours.
HMG PVC Pro Colours performs very well when coating window frames, reducing the risk of window seals adhering to the coating.
Available in packs of 1 or packs of 6+, 50 and 100 with discounted price breaks.
| Technical Data | |
|---|---|
| Volume Solids: | 11.9% |
| VOC Content: | - |
| SG: | - |
| Viscosity: | - |
| Density: | 0.766g/cm³ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed |
| Shelf Life: | 12 months from delivery date in original sealed containers |
| Flash Point: | -42°C |
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Aerosol: | 20-25 microns | 100 microns | |
Coverage: 10.5 square metres per litre @ 20 microns dft
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 10-15 minutes |
| Hard Dry: | 45-60 minutes |
| Technical Data | |||||
|---|---|---|---|---|---|
| Aerosol | |||||
| Mixing Ratio: | Ready for use | ||||
| - | |||||
| Thinner Options: | - | ||||
| - | |||||
| Viscosity: | Ready for use | ||||
| Spray Gun Setup: | - | ||||
| Number Of Coats (Guide Only): | 1 - 2 full coats | ||||
| Flash Off: | 10 - 15 minutes between coats | ||||
Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
| Information on basic physical and chemical properties | |
|---|---|
| Form: | Aerosol |
| Colour: | According to product specification |
| Odour: | Characteristic |
| Odour Threshold: | Not determined |
| pH-value: | Not determined |
| Change in Condition | |
| Melting point/freezing point: | Undetermined |
| Initial boiling point and boiling range: | -24.9°C |
| Flash Point: | -42°C |
| Flammability (solid, gas): | Not applicable |
| Ignition temperature: | 315°C |
| Decomposition temperature: | Not determined |
| Auto-ignition temperature: | Product is not self igniting |
| Explosive properties: | Heating may cause an explosion |
| Explosion limits: Lower: | 1.2 Vol % |
| Explosion limits: Upper: | 18.6 Vol % |
| Vapour pressure at 20°C: | 5200 hPa |
| Density at 20°C: | 0.766 g/cm³ |
| Relative density: | Not determined |
| Vapour density: | Not determined |
| Evaporation rate: | Not determined |
| Solubility in / Miscibility with water: | NOT MISCIBLE |
| Partition coefficient: n-octanol/water: | Not determined |
| Viscosity: Dynamic at 20°C: | Not determined |
| Viscosity: Kinematic: | Not determined |
| Solvent content: Organic solvents: | 88.00% |
| Solids content: | 11.9% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 HO on 2022-01-31 12:21:46 | Question:
I am going repaint my front UPVC door, both front and back. How many cans would I need and is a primer or any prep required? |
Answer from Rawlins’ Technical Team:
HMG would recommend 2 to 3 cans will be required, film thickness and hiding power on aerosols is a lot less than with a standard wet paint. Assuming the UPVC door is clean, dry, sound and prepared as detailed in the technical data sheet no primer would be required. HMG also not recommend using aerosols for full substrates because of reduced hiding, aerosols are really designed for touch-up. | |
| Nicole Haroutunian on 2021-09-20 22:43:04 | Question:
Hi there, I'm planning on refreshing a faux leather set of drawers (bedside table size) and wanted to check whether this spray paint would provide suitable coverage for the faux leather material. The drawers are brown and I'd like to paint them a lighter colour. Many thanks, Nicole |
Answer from Rawlins’ Technical Team:
No, this product is only for application to UPVC, but assuming the faux leather drawers are vinyl, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Technispray Vinylkote. | |
HMG Prep Clean 2805 is a medium strength, anti static preparatory cleaning solvent. Suitable for degreasing of new u-PVC and other plastic substrates More Information Delivery Info
HMG Prep Clean 2806 is a strong preparatory cleaning solvent. Suitable for degreasing of old u-PVC substrates. More Information Delivery Info
HMG PVC Pro Colours is specifically developed to adhere to uPVC substrates to renovate window frames, conservatories and doors. This product has also been designed to be “Ready for Use”, allowing it to be applied straight from the tin via brush or spray application. Highly flexible Good long-term durability Quick drying Available in...
