HMG Coach Enamel Aerosol is a traditional, ultra high quality, high build, long oil synthetic enamel. It gives ultimate high gloss, build and scratch filling combined with excellent water resistance, flexibility and good exterior durability and toughness. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG Coach Enamel.
400ml/16oz Aerosol
Available in packs of 1 or packs of 6+, 50 and 100 with discounted price breaks
High gloss
Excellent water resistance
Flexible with good exterior durability and toughness
Touch dry in 3hrs @20°C
Available in 3,500 colours from RAL, NCS, and British Standard
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cart
HMG Coach Enamel Aerosol is a traditional, ultra high quality, high build, long oil synthetic enamel. It gives ultimate high gloss, build and scratch filling combined with excellent water resistance, flexibility and good exterior durability and toughness. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG Coach Enamel.
Available in packs of 1 or packs of 6+, 50 and 100 with discounted price breaks
High gloss
Excellent water resistance
Flexible with good exterior durability and toughness
Touch dry in 3hrs @20°C
Available in 3,500 colours from RAL, NCS, and British Standard
Product Specification
Technical Data
Volume Solids:
31.9%
VOC Content:
0.380kgs/ltr
SG:
-
Viscosity:
-
Density:
0.845 g/cm³
Storage Conditions:
Store between 5°C - 25°C. When not in use, cans must be kept sealed
Shelf Life:
12 months from delivery date in original sealed containers
Flash Point:
- 42°C
Film Thickness Range And Coverage
Product Data
Dry Film Thickness
Wet Film Thickness
Aerosol:
50 µm
100 µm
Coverage: 10 square metres per litre @ 50 microns dft.
HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness
These values are a guide only and are not to be used as specifications
Film thickness will vary depending on actual use and specification
Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness
Drying Times
Drying Times At 20°C
Touch Dry:
3 hours
Hard Dry:
12 hours
Dry To Recoat:
After 24 hours
Fully Cured:
24 hours
Surface Preparation
Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants
Application Methods
Technical Data
Aerosol
Mixing Ratio:
Ready For Use
-
Thinner Options:
-
-
Viscosity:
-
Number Of Coats (Guide Only):
1 - 2 coats
Flash Off:
-
Product Notes
Information on basic physical and chemical properties
Form:
Aerosol
Colour:
According to product specification
Odour:
Characteristic
Odour Threshold:
Not determined
pH-value:
Not determined
Change in Condition
Melting point/freezing point:
Undetermined
Initial boiling point and boiling range:
-24C
Flash Point:
-42°C
Flammability (solid, gas):
Not applicable
Ignition temperature:
>200°C
Decomposition temperature:
Not determined
Auto-ignition temperature:
Product is not selfigniting
Explosive properties:
Heating may cause an explosion
Explosion limits: Lower:
0.6 Vol %
Explosion limits: Upper:
18.6 Vol %
Vapour pressure at 20°C:
5200 hPa
Density at 20°C:
0.845 g/cm³
Relative density:
Not determind
Vapour density:
Not determind
Evaporation rate:
Not determind
Solubility in / Miscibility with water:
NOT MISCIBLE
Partition coefficient:n-octanol/water:
Not determined
Viscosity: Dynamic at 20°C:
Not determined
Viscosity: Kinematic:
Not determined
Solvent content: Organic solvents:
61.3%
Solids content:
31.9%
Health & Safety
Refer to the Safety Data Sheet in the attachments section above and tin label prior to use
Suitable respiratory equipment should be worn when spraying
Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid
Product Details
5711-891715
Data sheet
Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
For Use On
Metal
Application Method
Aerosol
Sheen
Matt Satin Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Single
Pack Size
400ml/16oz Aerosol
Key Features
High gloss. Excellent water resistance. Flexible with good exterior durability and toughness.
Touch Dry (at 20°C)
3 Hours
Dry to Handle (at 20°C)
12 Hours
Dry to Recoat (at 20°C)
After 24 Hours
Fully Cured (at 20°C)
24 Hours
Coverage
10 square metres per litre @ 50 microns dft (Theoretical)
Density
1.055 g/cm³
Solids by Volume
31.9 %
Heat Resistance (up-to)
90°C
VOC
0.380kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Coach Enamel Aerosol is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
HMG Coach Enamel is traditional, ultra high quality, high build, long oil synthetic enamel for brush application. It gives an extra long wet edge time allowing it to be brushed without brush drag.High gloss Excellent water resistance Flexible with good exterior durability and toughness Available in 3,500 colours from RAL, NCS, and...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...