Rust-Oleum NeverWet

Reference: AE034-UK

Manufacturer:

Rust-Oleum NeverWet is a superhydrophobic treatment that dramatically repels water, mud, ice and other liquids. This revolutionary surface treatment causes water to form nearly perfect spheres that roll off coated items, keeping them clean and dry.

Bulk Buy

£19.95 tax excl.

Product Description

Rust-Oleum NeverWet is a superhydrophobic treatment that dramatically repels water, mud, ice and other liquids. This revolutionary surface treatment causes water to form nearly perfect spheres that roll off coated items, keeping them clean and dry. The pack contains a 2-step kit consisting of an aerosol base coat and an aerosol top coat that will cover approximately 1m².

Rust-Oleum NeverWet contains breakthrough technology that protects surfaces with a superhydrophobic treatment that dramatically repels water, mud, ice and other liquids. This revolutionary new class of treatments causes liquids to form nearly perfect spheres, which shoot off the surface keeping items clean and dry. It also guards virtually any surface against corrosion and wear caused by exposure to moisture.

Rust-Oleum NeverWet causes water droplets to form a contact angle of up to 165 degrees, more than three times the contact angle of an untreated surface. When a liquid hits an untreated surface, it pools on the surface, like a deflated ball, causing the item to become saturated. When water, mud and ice contact a NeverWet treated surface, the extreme contact angle causes the liquid to form nearly perfect spheres, like marbles of water. The spheres then glide off the surface, keeping the item clean and dry.

Applications

Rust-Oleum NeverWet can be applied to almost any surface including metal, wood, aluminium, PVC, concrete, masonry, asphalt, fibreglass, canvas and most plastics. It can also be used on fabric, leather and canvas but is not recommended for clothing.

Features & Benefits

  • Protects virtually any surface
  • Easy to apply
  • For interior and exterior use
  • Sprays clear – dries to a flat, frosted finish. May leave a slightly chalky feel
  • Can also be used on fabric, leather and canvas – not recommended for clothing

Application Tutorial
Follow our simple step-by-step tutorial to help ensure you get the best finish possible. Rust-oleum NeverWet is a two-step kit. Both the base coat and top coat must be used. The kit will cover approximately 1m².

  1. Surface preparation: Remove all dirt and debris from area to be coated. Cover and mask-off areas to avoid overspray if necessary.
  2. Basecoat application: Shake the can vigorously for one minute after the mixing ball begins to rattle. If the mixing ball fails to rattle DO NOT STRIKE CAN, contact the Technical Department. A test spray on cardboard is recommended to obtain a feel for the spray pattern. Hold the can upright 15-30cm from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Continue to shake the can between passes. Keep the can the same distance from the surface. Keep the can in motion while spraying. Apply two or more base coats 15 minutes apart. Allow to dry for at least 30 minutes before applying the topcoat.
  3. Topcoat application: Again, shake the can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN, contact the Technical Department. A test spray on cardboard is recommended to obtain a feel for the spray pattern. Hold the can upright 15-30cm from surface and spray in one steady pass. Avoid soaking the surface. Stop and wait for each pass to dry for 1-2 minutes. Three or four coats will give optimum results. Do not apply any other topcoat other than NeverWet™ as it will lose its moisture repellent properties.
  4. Drying: Wait at least 30 minutes before exposing the treated surface to water. Best performance is achieved if the coating is allowed to cure for 12 hours.
  5. Clean Up: When finished spraying, wipe off the tip before storing. Clean up wet or dry coating with white spirits or xylene.

Note: Rust-Oleum NeverWet can be re-applied when water no longer beads and rolls of the surface.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions



questions Sally Myburgh on 16/03/2017
Question: I can see no reference to the coverage of this product. Can you tell me what area one pack would cover?
Answer: 

The pack contains a 2-step kit consisting of an aerosol base coat and an aerosol top coat that will cover approximately 1m².

questions Scott cooke on 19/11/2016
Question: Hello I've seen this product on YouTube and was highly impressed with it. My question is would this product work on clothing or is it more suited to none clothing objects.

Many thanks
Answer: 

Rust-Oleum NeverWet can be applied to almost any surface including metal, wood, aluminium, PVC, concrete, masonry, asphalt, fibreglass, canvas and most plastics. It can also be used on fabric, leather and canvas but is not recommended for clothing.

Question about the product

* Required fields
Send

The question has been correctly sent

Free delivery

On orders over
£75.00 + VAT

Low trade prices

Our best trade prices on everything!

Technical Advice

Fast FREE Technical Advice for Products & Projects

Click & collect

Order and collect from
our Leeds based trade store.
silent-exothermic unable