506 Anti Slip Dressing
506 Anti Slip Dressing is sold in 10m² packs with each contain a flexible binding resin and decorative aggregate to create a `stone carpet` finish which gives the appearance of loose aggregate, but avoids maintenance problems. Primarily used on outdoor walkways and concourse areas but can also be used internally to reflect the natural beauty of the outdoors.
This product is temporarily out-of-stock. Please contact a member of our Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information or suitable alternatives.
See our Customer News page for the latest updates on COVID-19 and business availability.
506 Anti Slip Dressing is sold in 10m² packs with each contain a flexible binding resin and decorative aggregate to create a 'stone carpet' finish which gives the appearance of loose aggregate, but avoids maintenance problems. Primarily used on outdoor walkways and concourse areas but can also be used internally to reflect the natural beauty of the outdoors.
506 Anti Slip Dressing is a seamless bonded aggregate system with high wear and slip resistance. The flexible binder is suitable for bonding the loose decorative aggregate to concrete, tarmac and asphalt. The system can be finished with a clear sealer if required to enhance the decorative effect, and to obviate staining – this is an optional extra and must be purchased separately.
506 Anti Slip Dressing is suited to areas subject to heavy footfall and vehicular traffic such as leisure complexes, theme parks, holiday resorts, national trust sites, car parks and much more.
- Tough & hard wearing
- Excellent abrasion & impact resistance
- Good chemical resistance
- Low odour during application
- Rapid Curing
- Easy to clean
- Permeable (breathable)
- Wide range of colours and decorative effects
- Slip resistant
- As a decorative anti-slip floor covering for internal and external walkways and concourse areas.
- Suitable for use on concrete, tarmac and asphalt.
- Used at parks, shops, restaurants, sports venues, leisure complexes, theme parks, holiday resorts, national trust sites, car parks and much more.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
|Jill on 2019-11-25 13:08:27|| |
Will this product level out minor rippling on a concrete surface and cover construction joints in the site cast concrete ground?
506 Anti Slip Dressing is a thick system so it should mask minor finishing marks in concrete. Covering construction joints shouldn’t be a problem either as the material has a good amount of flexibility. That being said, if there is considerable movement along the joints this may cause cracks to appear in the surface.
|Ian on 2019-09-06 11:48:39|| |
What thickness is recommended ?
10m² packs include 15kg of binder resin with hardener which must not be spread further than 10m² and 50kg of 1-3mm Chinese Bauxite Aggregate to broadcast over the wet resin.
|claire yakoob on 2019-06-01 10:00:01|| |
Can this product be used to cover vertical and horizontal steps?
This product is not suitable for vertical surfaces, only level, horizontal ones.
|John Ridley on 2019-05-08 10:05:03|| |
506 Anti Slip Dressing What's it made of? How do you stick it onto the tarmac? Can it be cut easily? How long do you expect to last? Many thanks John
506 Anti-Slip Dressing is a seamless bonded aggregate system with high wear and slip resistance. Each pack comprises a flexible binder suitable for bonding the loose Quartz or Stone decorative aggregates to concrete, tarmac/asphalt and sufficient aggregate. New tarmac must be allowed to weather until all residual oils have been oxidized or been removed. Thoroughly wash to remove contaminants and allow to dry.
Apply the mixed Binder Resin by roller, serrated trowel, or squeegee at the required spreading rate. Whilst the Binder Resin remains wet, broadcast the selected aggregate to achieve a full 'blinding' i.e. leave no resin visible. The following day thoroughly sweep off any excess aggregate using a stiff bristled broom.
|Bryn Davies on 2017-11-23 12:34:14|| |
Question: Please can you provide me with the 'R' Rating value for this product Thanks Bryn
The product hasn't been tested to determine its R value as we do not offer the product for any thermal conductivity or insulating properties.