Ennis-Flint Stonegrip is a specialist, hand applied surface treatment, consisting of a thermosetting, modified epoxy resin binder, dressed with a decorative aggregate. A wide range of aggregates are available comprising of different colours and sizes.
Ennis-Flint MMAXGRIP PRMX 65
Ennis-Flint MMAXGRIP PRMX 65 is a MMA-based coating that was developed specifically for application to public main roads and side streets as well as other traffic zones. Its special properties make MMAXGRIP PRMX 65 particularly suitable for surfaces where coloured road markings are required on main roads and side streets in urban areas and elsewhere.
Ennis-Flint MMAXGRIP PRMX 65 is a MMA-based coating (MMA – polymethyl methacrylate) that was developed specifically for application to public main roads and side streets as well as other traffic zones. Its special properties make MMAXGRIP PRMX 65 particularly suitable for surfaces where coloured road markings are required.
Features & Benefits
- Superior abrasion-resistance, PSV of aggregate 70-80
- Superior skid resistance and grip > SRT 65 (SN 640 214 FGSO)
- Resistant to mechanical stress
- Easy and fast application
Areas of Application
MMAXGRIP PRMX 65 is suitable for use as coloured surface markings applied on main roads and side streets in urban areas and elsewhere (including plazas, cycle tracks, footpaths, pavements and byways).
Included in Pack
- 15.00kg MMAXGRIP PRMX 65
IMPORTANT: Ennis-Flint MMAXGRIP PRMX Catalyst MUST be purchased separately in order to use this product. The required quantity for the application conditions such be purchased accordingly (see below).
Reaction Times and Required amounts of Catalyst
|Pot life||12 min.|
|Fully cured||2 hours|
Higher temperatures or greater proportions of catalyst will shorten reaction times, while lower temperatures and smaller proportions of catalyst will extend reaction times. The following table indicates the recommended amount of catalyst required to adjust the curing reaction to the temperature.
|Substrate temperature in °C; required amounts of catalyst in % w/w (guide)|
|MMAXGRIP PRMX Catalyst||3%||3%||2%||2%||1.5%||1.5%||1.5%||1%||1%||1%|
The substrate must be suitably prepared so that it is sound, dry and free from loose or adhesion-reducing components.
Ennis-Flint MMAXGRIP PRMX Primer is used as a primer on absorbent substrates, e.g. concrete. For further information, please refer to the technical information sheet.
We advise against applying the product to fresh asphalt < 90d. No primer is required if the product is applied to older asphalt > 90d.
First stir the tub contents thoroughly. The add the catalyst while stirring at the slow-speed setting and mix for at least 2 minutes. Make sure that the product on the base and sides of the container is incorporated. Ideally MMAXGRIP PRMX 65 should be repotted once then stirred thoroughly again. At product temperatures <10 ˚C the product should be stirred for at least 4 minutes, as the catalyst will take longer to dissolve.
Spread the mixed material evenly using the smoothing trowel, aluminium blade or rubber squeegee and lay off to particle size thickness. For an even surface with a good grip (SRT > 65) the area must be finished with a textured roller immediately after application.
NOTE: Ennis-Flint MMAXGRIP PRMX 65 is subject to a 7 - 10 working day lead time. It is also available in all RAL colours, except effect colours. Please contact us for further details. Additional costs and extended lead times may be applicable.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Sikafloor 264 N Thixo is a two part, economic, coloured epoxy resin textured roller and seal coat. This Sikafloor product is solvent free, thixothropic grade for high build textured and structured finishes.
Resubind CP, a 3 component, non-pigmented, solvent-free polyurethane binder designed for car park decks, walkways and driveways, surface dressed with aggregates to create non-slip, hard wearing, textured floor finishes. Can be used in interior or exterior car park decks on a variety of substrates. Different aggregates can be used to create...
A one coat, hard wearing epoxy resin anti-slip coating for concrete, stone, metal and wood. Solvent-free and virtually odour-free, Rust-Oleum SuperGrip Treadsafe is finished with hard-wearing carborundum particles and will easily withstand heavy traffic including forklift trucks and harsh chemicals. Tough, long lasting finish Coarse...
Jotun Jota Armour WG is a Winter Grade version of the standard Jota Armour to allow faster curing in lower temperatures. It is a three component, abrasion resistant, polyamine cured epoxy coating specially designed as an anti-skid coating. Suitable for approved primers or directly on concrete substrates.
Axalta Highway Anti-Skid Traffic Paint is a highly durable, fast drying, low-slip traffic paint based on a specially modified chlorinated rubber system. The coating is coloured with chemical and weather resistant pigments. developed as a traffic line / parking bay paint with low-slip properties, suitable for application to asphalt, concrete,...
Smartkote Protectakote is a single component, ready-to-use, anti-slip coating with polyurethane performance for ultimate toughness. The course profile textured surface is ideal for interior floors, factory work-stations, walkways, stairs, ramps, vehicles and other areas where a flexible, durable and long lasting anti-slip surface is important....
Remmers Epoxy SIC Color is a textured, dissipative, hard grain coating that is conductive, provides slip-resistance, withstands mechanical/chemical loads and is physiologically harmless after curing.
Blackfriar Anti-Slip Deck Coating allows the beauty of wood and timber decking to show through. ADVANTAGES Provides a slip-resistant surface in wet conditions Clear, low sheen finish Ideal for foot traffic Can be applied over new or existing decking stains or bare timber Micro-aggregates give increased grip Excellent coverage
Rust-Oleum SuperGrip Anti-Slip Spray is a fast drying spray paint containing a special anti-slip additive. It can be applied on metal, concrete, ceramic and wood surfaces making virtually any surface non-skid instantly, ideal for small maintenance jobs or for touch-up. Light duty anti-slip finish Adheres to metal, wood, concrete, tile...
Teamac Suregrip Deck Paint, is a modified alkyd, ready mixed, aggregated deck coating which provides a rough anti-slip finish when dry Suitable for: Foot traffic Light truck traffic Use on wood Use on metal Use on concrete Use on GRP Available in a range of colours Click to jump down to Technical Data
Smartkote Protectakote UVR is a tough anti-slip aliphatic polyurethane coating, which forms a colour-fast, abrasion and weather resistant film. Protectakote UVR is single component, ready to use and easy to apply. Protectakote UVR is easy to apply and ideal to create anti-slip areas on exterior and interior surfaces.
Smartkote Protectakote WB Smooth is a water-based, smooth polyurethane coating. This water-based solvent-free formulation is weather resistant, has a low odour, and is non-flammable for both interior and exterior applications. It’s enhanced with polyurethane for ultimate toughness, with excellent resistance to abrasion, chemicals and solvents....
Coo-Var Anti-Slip Acrylic Floor Paint is used to provide a durable and hard wearing surface with an anti-slip finish. This product has been independently tested and has a PTV rating of 68 in dry conditions and 58 in wet. UK law recommends on a minimum Pendulum Test Value on floors of 36 dry, wet or contaminated. Product Features Low...
502 HD Anti Slip Coating is applied by brush or roller in one thick, durable coat and it will provide a heavily textured finish incorporating an anti-slip aggregate which is dispersed within the material upon application. Each pack contains sufficient material to provide a slip resistant epoxy coating system to 5 square metres of surface.
Smartkote Safekote is a ready-to-use polyurethane coating that provides an attractive, abrasion resistant anti-slip surface. The fine texture is provided by small silica particles which will not hurt bare feet, making it ideal for showers, change rooms, ablution blocks and other surfaces in environments such as hospitals, hotels or children’s...