Axalta ViterClad M50 Finish

2900 919/4054 122

Axalta ViterClad M50 Finish, a high performance two pack polyurethane metallic finish specially designed and tested for the maintenance repainting of architectural cladding.

  • Expected system lifetime up to 15 years (depending on exposed environment and shade)
  • Suitable for urban, marine and industrial environments
  • Tough, durable finish combining abrasion resistance with outstanding colour and sheen retention
  • Cures at sub-zero temperatures and has good climatic tolerance

**Available for delivery - see Delivery Options below**

Colour
Size
Finish
£164.90
VAT excluded

£197.88 Tax incl.
Quantity

Description

Axalta ViterClad M50 Finish is a two pack recoatable polyurethane finish with a metallic finish, specially formulated for the maintenance and repainting of architectural cladding. Recommended for the maintenance of Corus Colorcoat HP200 and HPS200 cladding, it has an expected system lifetime up to 15 years (depending on exposed environment and shade) and is suitable for PVF2, Silicone Polyester and Polyester Cladding (when applied over ViterClad Bonding Coat) in urban, marine and industrial environments.



Click To Jump To Section:




Features & Benefits


  • Recommended for the maintenance of Corus Colorcoat HP200 and HPS200 cladding
  • Expected system lifetime up to 15 years (depending on exposed environment and shade)
  • Suitable for PVF2, Silicone Polyester and Polyester Cladding when applied over ViterClad Bonding Coat
  • Suitable for urban, marine and industrial environments
  • Tough, durable finish combining abrasion resistance with outstanding colour and sheen retention
  • Good cleaning properties for ease of building maintenance
  • Cures at sub-zero temperatures and has good climatic tolerance
  • Tolerant of slight surface moisture during application



Product Specification


Technical Data
Volume Solids 42 ± 2% (may vary with colour)
VOC Content 471 + 20 g/litre (varies with colour)
SG 1.06-1.08 kg/lt mixed, varies with colour
Storage Conditions Store in dry, cool conditions and protect from frost
Shelf Life Minimum 12 months if stored as above in unopened containers
Flash Point 23-60℃



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Minimum 25 µm 60 µm 16.8 m² /litre
Maximum 60 µm 143 µm 7.0 m² /litre
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated



Drying Times


Product Data
Applied to 125 microns DFT 5℃ 10℃ 23℃ 35℃
Dust Free 3 hr 2 hr 1 hr 45 min
Hard Dry 9 hr 6 hr 3 hr 2 hr
Overcoating Minimum 24 hr 4 hr 12 hr 10 hr
Maximum Indefinite if clean and sound and sound
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation



Surface Preparation


  • This product is a finish coat which should be applied over ViterClad Bonding Coat or suitably prepared, sound Plastisol for recolour work
  • For aged/degraded Plastisol, condition diagnosis and correct surface preparation are critical to performance. Please consult Rawlins Technical Team for individual project specifications
  • Completely new and unweathered HP200* Plastisol must be wiped with white spirit (1050 Thinner) and allowed to dry prior to applying ViterClad 50
  • New HPS200* Plastisol must be wiped with xylene (1006 Thinner) and allowed to dry prior to applying ViterClad 50
  • For PVF2, Silicone Polyester and other cladding types, refer to Rawlins Technical Team 0113 2455450 (option 2) or [email protected]
  • Surfaces should be clean, dry and free from all grease, oil and general contamination



Mixing


Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator. Agitate periodically during use to ensure product remains homogeneous



Thinner


1737 Thinner

Equipment Cleaner - 1737 Thinner



Application Conditions


  • Only apply in conditions of good ventilation which must be maintained during drying and curing.
  • Do not apply in windy conditions where wind is likely to carry spray mist.
  • Do not apply when rain, mist, sleet or snow are imminent.
  • During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3ºC above the dew point.
  • Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process.
  • Paint temperature should ideally be at a minimum of 15ºC.
  • Do not apply above 40ºC.
  • Do not apply over standing or running water or ice.



Application Methods


  • Airless Spray: recommended for best finish. Output fluid pressure at tip 2000- 2500 psi, Tip Size: 11-13 thou (0.33-0.43mm). Up to 5% 1737 Thinner may be added for application under cool or hot conditions, but thinning should be avoided if possible
  • Conventional spray is possible but not recommended
  • Brush – not recommended due to metallic finish
  • Roller – use only good quality short hair roller types of suitable width to accommodate the cladding profile and configuration – always work from a wet edge. Up to 10% thinner may be required – use 1048 Thinner when applying by roller in warm conditions. Axalta Coating Systems strongly recommend that a feasibility test area is applied to confirm acceptable aesthetics are achievable



Product Notes


  • Contains isocyanates – refer to Safety Data Sheet
  • This coating has not been tested to the standard of the new regulation 7(2) of the Building Regulations 2010, which came into force in Dec 2018



Health & Safety


Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets - these sheets can be found in the attachments section above.

Click to go back to the top of the page

Product Details
2900 919/4054 122

Data sheet

Manufacturer
Axalta
For Use On
PVF2, Silicone Polyester, Plastisol
Application Method
Brush, Roller, Spray
Sheen
Semi-Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Parts
2
Mixing Ratio
Base - 8 parts by volume. Hardener - 1 part by volume
Application
Brush, Roller, Spray
Touch Dry (at 20°C)
1 hr
Dry to Recoat (at 20°C)
3 hr
Fully Cured (at 20°C)
12 hr
Coverage
7.0 to 16.8 m2 /litre (see data sheet)
Max. Application Temperature
40ºC
Min. Application Temperature
15ºC
VOC
471 + 20 g/litre (varies with colour)
Shelf Life (from date of manufacture)
Minimum 12 months if stored as above in unopened containers
Touch Dry
1 Hour
Recommended Dry Film Thickness
Min: 25 µm - Max: 60 µm
Recommended Wet Film Thickness
Min: 60 µm - Max: 143 µm
UN Number (Activator)
UN1263
UN Number (Base)
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Axalta 1048 Thinner

Axalta 1048 Thinner, for use with the Axalta range of coatings, is a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistancy for application whether it be for brush, roller or spray.  Can also be used for the cleaning of some surfaces prior to application of the coating...

Price £31.37
In stock

Axalta 1737 Thinner

Axalta 1737 Thinner, for use with the Axalta range of coatings, is a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistancy for application whether it be for Brush, Roller or Spray.  It can also be used for the cleaning of some surfaces prior to application of the coating...

Price £31.37
In stock

Axalta 1006 Thinner

Axalta 1006 Thinner, for use with the Axalta range of coatings has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray.  Can also be used for the cleaning of some surfaces prior to application of the coating...

Price £19.14
In stock