Rust-Oleum PVDF Primer is a single pack super adhesion primer for PVDF or PVF2, cladding sheets, galvanised steel, zinc and aluminium.
Features & Benefits
Excellent adhesion on PVDF (or PVF2) cladding
Also ideal primer for difficult metal substrates
Tack-free after only 30 minutes
Overcoat with NOXYDE® for years of protection
Single pack product
Technical Data
Density: 1,17
Gloss Level: Satin
Corrosion Class: C1/C2 low protection
Solids content in volume: 30 %
Solids Content in weight: 47 %
Drying Times At 20°C/RH 50%
Touch dry: 30 minutes
Dry to handle: 1,5 hours
Dry to recoat: 24 hours
Fully cured: 1 week
Theoretical Consumption
10 m²/l
Practical Consumption
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Surface Preparation
Remove grease, oil and all other surface contaminations by alkaline or high pressure cleaning in combination with appropriate detergents. Sand intact coatings to roughen the surface slightly. Remove zinc or aluminium corrosion with Surfa-Etch 108. The surface must be clean and dry
Remarks
Can be recoated with Fassilux , Fassilux Satin , Metal Cladding Topcoat and Noxyde. The PVDF Primer is a reversible paint that dissolves in its own solvent (= Thinner 22). Therefore, the PVDF Primer cannot be recoated with paints containing solvents with a stronger dissolving character than Thinner 22, f.i. xylene, toluene, etc. In case of doubt, a test should be done first. In order to establish if this primer is suitable for the respective substrate, we always advice to perform an adhesion test prior to application. Hydrophobicity: 95° contact angle with water (Cori test report ref. N/8384)
Product Details
281.5
Data sheet
Manufacturer
Rust-Oleum
Water / Solvent Based
Solvent
For Use On
Galvanized Steel, Zinc, Aluminium, PVDF, PVF2
Application Method
Brush, Roller, Spray, Airless Spray
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Dry to Handle (at 20°C)
1.30 Hours
Dry to Recoat (at 20°C)
24 Hours
Fully Cured (at 20°C)
1 Week
Coverage
10m² per litre
Density
1,17
Solids by Volume
30 %
VOC
570 g/l
Shelf Life (from date of manufacture)
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Good morning. I am intending to coat my garage roof with Noxyde Peganox. The roof is made out of good quality used Box Profile sheets that are a variety of different shades (mostly only spray finish including 1 or 2 Plasticol Coated) and within 2 miles of the coast. My question is: If using Peganox, do I also need to use an undercoat on these sheets, particularly the Plasticol finish ones? Kind regards. Gus Flowers
Answer:
Assuming the roof is pitched and surfaces are aged, weathered (2+ years) then we would recommend the application of Rust-Oleum Mathys Noxyde Pegarust directly to the sheets in two coats. Rust-Oleum Mathys Noxyde Pegarust is a primer and topcoat in one and can be applied directly on various metallic substrates including weathered/aged iron, galvanised steel, plastisol, aluminium and zinc.
Rust-Oleum Mathys Noxyde Peganox should not be used on roofs and Rust-Oleum PVDF Primer would not be needed in this instance presuming your surfaces are one of the above mentioned and are weathered/aged.
We no longer stock this product, but can recommend Zinsser AllCoat Exterior Satin (Solvent Based) as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...
Rust-Oleum Mathys 108 Surfa Etch Solution is an easy to use, non-flammable and virtually odour free etching solution for the preparation of smooth concrete surfaces, masonry, galvanized steel and aluminum before applying a paint coating system.
Improves the adhesion of coating systems
Neutralizes alkaline salts
Also ideal to remove "white...
Rust-Oleum Thinner 22 is for the dilution of synthetic enamels and varnishes for airless application. Degreasing of metals and most wood types. Cleaning of `spots` of acrylic paints and acrylic fixing paints (e.g. on glass).
Best used to dilute the following products:
Primer 44
Fassiclor
Galvaprim
Vernac Gloss
Vernac Satin
More...
Rust-Oleum Mathys Noxyde is a single pack, water-based elastomeric coating with unequaled corrosion protection designed for spraying, offering 20 years of protection with excellent waterproofing and elasticity.
Primer and topcoat in one
16 colours available
Anthracite Grey RAL 7016 temporarily unavailable
Impact resistant
Prevents rust...
Rust-Oleum Mathys Metal Cladding Topcoat is a long lasting water based, semi-gloss acrylic paint specially designed for use as a finish on exterior metal cladding that has high filling and hiding power and features excellent flow out with high durability and colour and gloss stability.
Choose from 4,100+ colours in RAL, BS and NCS shades...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Click to jump down to...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage