- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
We no longer stock this product, but can recommend Bradite One Can as a great alternative.
Product customisation
Don't forget to save your customization to be able to add to cartWe no longer stock this product, but can recommend Bradite One Can as a great alternative.
Bradite Cladit is a colourful cladding paint for use on steel structures and cladding, plastisol and PVF2. There is no need to use primer, so long as the cladding is intact, you can apply this cladding paint to provide a hard-wearing and flexible protective coating.
Additionally, Bradite Cladit can be applied to suitably prepared and primed steel, non-ferrous steel, fibreglass, concrete and mineral substrates.
Touch dry in as little as 1 hour, the semi-gloss finish can be achieved using a brush, roller or spray.
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/d wb): 130g/l (2010). This product contains max.7 g/l VOC.
Features & Benefits
- Available in more than 350 colours in RAL & BS
- For use on steel structures and cladding.
- Suitable for both wall and roof areas.
- Hard-wearing and flexible coating.
- No need for primer, apply directly to intact cladding.
- water-based coating with low VOCs.
- Dries quick.
Preparation
High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent washing and rinsing should be used with scrubbing to remove grease or oil.
Check & confirm adhesion of apparently sound cladding coating by carrying out cross hatch adhesion test to all elevations. If adhesion is suspect then elevation should be completely stripped of old coating and repainted.
Intact areas of existing coatings should, ideally, be roughened by manual or mechanical sanding. Feather back exposed areas to a sound coating edge. Cracks and pits should be filled using a suitable filler before painting. Substrate should be dust free and completely dry before coating.
Exposed ferrous & non-ferrous substrates should be blast cleaned to SIS Sa21/2 or manually cleaned to SIS St3, then patch primed with Bradite SORTED WP45 primer.
Priming coat: Bradite SORTED WP45, if required.
1st coat: Bradite Cladit WC44.
2nd coat: Bradite Cladit WC44.
Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.
Application
Always aim to paint an elevation preceding direct sunlight illumination to prevent painting onto warm surfaces which may cause too rapid drying and detract from application properties and finish appearance quality. Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.
Brush and Roller: Supplied ready for use. Thin with 0-5% water if required.
Conventional Air Spraying: Thin with 10 - 20% water as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately. Airless Spraying - Thin with 0-15% water as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately.
Clean all equipment immediately after use with water for best results.
Data sheet
- Manufacturer
- Bradite
- Interior / Exterior Use
- Exterior
- Water / Solvent Based
- Water
- For Use On
- Plastisol, Powder Coatings, Steel, Non-ferrous metals
- Application Method
- Brush, Roller, Spray, Airless Spray
- Sheen
- Semi-Gloss
- Colour
- Fully Tintable
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Single
- Product Certifications
- ISO 9001:2008, ISO 14001:2004 environmental management systems
- Pack Size
- 5L
- Brand
- Bradite
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Bradite Cladit is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT