- There are no more items in your cart
- Shipping Calculated at checkout
- Total £0.00
Call 0113 245 5450 for Sales or Technical
Alternatively you can email our sales & support team on [email protected]
Coronavirus Updates - Open and Services as Normal (click for more info)
Rust-Oleum Mathys ND14 Cleaner Degreaser
14.5
Rust-Oleum Mathys Alkaline Cleaner/Degreaser ND14 should be used to remove grease, oil, proteins, dirt and many other surface contaminants from coated, mineral and steel substrates.
- Concentrated formulation can be diluted 1:20
- Use as additive for high pressure cleaning
- Non-flammable, virtually odour-free
Description
Rust-Oleum Mathys ND14 Cleaner Degreaser
Concentrated alkaline cleaner degreaser
Removes grease, oil, proteins , dirt and many other contaminants from coated, mineral and steel substrates
Rust-Oleum Mathys Alkaline Cleaner/Degreaser ND14 should be used to remove grease, oil, proteins, dirt and many other surface contaminants from coated, mineral and steel substrates.
Features and Benefits
- Non-flammable, virtually odour-free cleaning/degreasing solution.
- Can be used as an additive for high pressure and steam cleaning
- Applied by synthetic sponge, cloth, brush or broom
- Low concentration (3-5% is sufficient for most cleaning)
Technical Data
Density: 1,18
Theoretical Consumption
The content of the concentrated 5 litre packaging will allow you to treat a surface of up to 500 m², based on a dilution of 1:20
Practical Consumption
Practical usage depends on many factors such as type and amount of contaminants, shape of the substrate and material losses during application.
Directions For Use
To ensure homogeneity shake well before use. Scrape or sweep away grease, oil, dirt, mould and all other surface contaminations as much as possible. ND14 Cleaner/Degreaser can be applied diluted or concentrated with a sponge, cloth, brush or broom. For normal cleaning a 3 - 5% concentration will be sufficient. The product should be diluted with cold water. After use rinse with plenty of fresh water. If a concentration of more than 5% is used, hot water rinsing is absolutely necessary. As a high-pressure(steam)cleaning additive a 2% concentration is recommended. After cleaning, remove any remaining water and allow the surface to dry, as moisture left on the surface or entrapped into pores may cause premature failure of the coating system. Large surface areas or poor drying conditions may require longer drying times before a coating system can be applied.
Application Conditions
Temperature of air, substrate and material between 5 and 35°C.
Remarks
If used on galvanized steel, zinc, aluminum or anodized aluminum rinse the surface excessively.
Safety Data
- pH: 12
- VOC level: 92 g/l
- Remarks regarding safety: Consult Safety Data Sheet and Safety Information printed on the can
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Product Details
14.5
Data sheet
- Application
- Brush
- Coverage
- 6-8m² per litre
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 5°C
- Density
- 1,18
- VOC
- 92 g/l
- Shelf Life (from date of manufacture)
- 2 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
- UN Number
- UN1824
 sva on 2017-03-07 18:00:02 | Question: Hi is this cleaner environment friendly? Specially around animals such as horses goats chicken etc Thanks |
Answer: Information regarding the safety of the product can be found in the MSDS (Material Safety Data Sheet) available to download from the 'DATASHEETS' tab above. | |