Axalta ViterClene C Degreasing Solution

4077 050

Axalta ViterClene ‘C’ Degreasing Solution, a single pack bio-degradable detergent wash, for the efficient removal of dirt, oil or grease prior to painting. Specially formulated for use with ViterClad cladding coatings.

  • Specifically recommended for cleaning Plastisol or other sheeting prior to coating with ViterClad systems
  • Effective for cleaning aged coatings or bare substrates of oil, grease or dirt prior to coating
  • A bio-degradable product which after application can be washed away through domestic drainage with sufficient clean water diluent
  • Concentrated – can be diluted up to 20:1 with water

Size
£52.56
VAT excluded

£63.07 Tax incl.
Quantity

Description

Axalta ViterClene ‘C’ Degreasing Solution, a single pack bio-degradable detergent wash, for the efficient removal of dirt, oil or grease prior to painting. Specially formulated for use with ViterClad cladding coatings.

Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected]



Click To Jump To Section:




Features & Benefits


  • Specifically recommended for cleaning Plastisol or other sheeting prior to coating with ViterClad systems
  • For the cleaning of aged coatings or bare substrates of oil, grease or dirt prior to coating.
  • Bio-degradable product which after application can be washed away through domestic drainage with sufficient clean water diluent.
  • An effective degreaser for galvanising.
  • Concentrated – can be diluted up to 20:1 with water.
  • Can be applied by brush, or airless spray.



Product Specification


Technical Data
Volume Solids n/a
VOC Content 417 + 20 g/litre
SG 0.96-0.98 kg/lt
Storage Conditions Store in dry, cool conditions and protect from frost.
Shelf Life Minimum 12 months if stored as above in unopened containers.
Flash Point 23-60℃



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Minimum n/a n/a 15 m² /litre²
Maximum n/a n/a
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.



Drying Times


Temperature
  10℃ 23℃ 35℃
Drying Time: Allow 10 - 15 minutes, then flush with water.



Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.



Surface Preparation


Remove thick films of grease with a scraper or rags prior to application of ViterClene ‘C’.



Mixing


Ensure solution is homogenous before use.



Thinner


Clean water.

Clean water can also be used to clean equpment.



Application Conditions


  • Only apply in conditions of good ventilation which must be maintained during drying.
  • Do not apply when rain, mist, sleet or snow are imminent.
  • During application and drying time of the wash solution, the Relative Humidity should not exceed 88% and the steel temperature should remain at least 2℃ above the dew point.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No Yes No



Any areas of stubborn contamination should be removed by vigorous application using e.g. brushes or clean rags, followed by thorough rinsing and allowing to dry. Ensure that all traces of contamination and residues are thoroughly removed before applying any coatings.

    • Apply by brush or clean rags (recommended), or by airless spray.
    • Apply ViterClene ‘C’ in accordance with the dilution described below, preferably using warm water rather than cold water. Allow 10 – 15 minutes for penetration, then water wash with potable water (pressure washing or rinsing with scrubbing is recommended) to remove all residues, and allow to dry before applying any coating.
    • Any areas of stubborn contamination should be removed by vigorous application using e.g. brushes or clean rags, followed by thorough rinsing and allowing to dry. Ensure that all traces of contamination and residues are thoroughly removed before applying any coatings.
    • Reduce dilution as necessary in accordance with surface conditions.

Dilution:

    • Heavy soiling – apply neat
    • Medium soiling (light oil, grease, general dirt) - dilute 5:1 with clean water
    • Light soiling (hydraulic oils, light grease) - dilute 10:1 with clean water
    • General cleaning (light dirt only) - dilute 20:1 with clean water



Product Notes


In any cleaning operation, the aim is to remove dirt from the surface.  This can be achieved by loosening the dirt and washing it away with e.g. a water spray, hose pipe, etc., or by wiping it off the surface with rags, which will need changing frequently for fresh, clean ones.  Using the same piece of rag or brush repeatedly without rinsing can result in the dirt simply being redistributed around the surface, and not removed.



Health & Safety


Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets. A Safety Data Sheet for this product is available on request from Axalta Coating Systems or on our attachments section above.

Click to go back to the top of the page

Product Details
4077 050

Data sheet

Manufacturer
Axalta Coating Systems
Application Method
Brush, Airless Spray, Rag
Single, Two or Three Pack
Single
Pack Size
5L
Parts
Single part pack
Dry to Handle (at 20°C)
10 – 15 minutes, then flush with water. Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Coverage
15m² per litre
Recommended Thinner/Cleaner
Clean water
Max. Application Temperature
Relative Humidity should not exceed 88%
Min. Application Temperature
Steel temperature should remain at least 2℃
Min. Application Temperature
Steel temperature should remain at least 2℃ above the dew point.
VOC
417 + 20 g/litre
Shelf Life (from date of manufacture)
Minimum 12 months if stored as above in unopened containers
Recommended Dry Film Thickness
N/A
Recommended Wet Film Thickness
N/A
UN Number
Not regulated
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send