Teamac Mordant Solution (T Wash)

420/MORDANT
TEA782

Teamac Mordant Solution (T Wash), is a pre-treatment for new galvanised steel to ensure adhesion of subsequent coatings.  Satisfactory treatment will be shown by a colour change to dark grey throughout the whole surface.

Advantages

  • Application: Brush, Dip, Roller
  • Coverage: 40 Square Metres Per Litre
  • Suitable For: Galvanised Metal
  • Drying Times: Touch Dry: 1.5 - 2 hours
  • Click to jump down to Technical Data

Size
£40.37(ex. VAT)
£48.44 (inc. VAT)
Quantity
Please choose your colour
In Stock and Available for Delivery (See Delivery Options Below)

Description

Teamac Mordant Solution (T Wash), is a pre-treatment for new galvanised steel to ensure adhesion of subsequent coatings.  Satisfactory treatment will be shown by a colour change to dark grey throughout the whole surface.



Click To Jump To Section:




Features & Benefits


Advantages

  • Application: Brush, Dip, Roller
  • Coverage: 40 Square Metres Per Litre
  • Suitable For: Galvanised Metal
  • Drying Times: Touch Dry: 1.5 - 2 hours
  • Click to jump down to Technical Data



Product Specification


Technical Data
Volume Solids N/A
VOC Content Max 325 g/litre
SG 1.01 to 1.02°C
Viscostity Thin solution
Flash Point 31°C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum N/A N/A 40 m2/litre



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 1.5 - 2 hours
Dry To Handle: N/A
Dry To Recoat: Do not recoat
Fully Cured: N/A



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Apply to new galvanising within 7 days.
  • Zinc surfaces which are contaminated should be cleaned down using an abrasive pad, water and cleaning agent followed by rinsing and allowing to dry.
  • If contaminated with oil or grease surfaces should be wiped over with Universal Degreaser before carrying out the cleaning down procedure.
  • Can be applied to weathered galvanised surfaces although reactivity of the treatment will diminish as the age of the galvanising increases and can result in an uneven colouration from light grey to dark grey.  If no colour change takes place, these areas should be considered as contaminated.



Preceeding Coat


  • None



Mixing


  • N/A



Application Conditions


  • As dictated by normal good painting practice.  In confined spaces, provide adequate ventilation during application and drying.
  • Many metallic surfaces are slowly attacked by Mordant Solution (T Wash).  This must be borne in mind if spraying is considered.  Guns and equipment may be damaged and must be washed thoroughly with fresh water immediately after each work period.



Application Special Conditions


  • Within 7 days of galvanising. 
  • Only to degreased and uncontaminated surfaces.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  No No Yes Yes



  • Thinner (Max vol): N/A
  • Nozzle Size: N/A
  • Nozzle Pressure: N/A
  • Cleaning Solvent: Clean Water



Health & Safety


See safety data sheet - SDS 10847 - in attachement section above.

Click to go back to the top of the page

Product Details
782-779592

Data sheet

Manufacturer
Teamac
Pack Size
2.5L
Suitable Substrates
Galvanised Metal
Application
Brush, Roller
Touch Dry (at 20°C)
1.5 - 2 hour
Dry to Recoat (at 20°C)
Do not recoat
Coverage
40 m2/litre
Solids by Volume
N/A
VOC
Max 325 g/litre
Size
5 litre polythene bottles
Recommended Dry Film Thickness
N/A
Recommended Wet Film Thickness
N/A
UN Number
1263
Suitable For Use On
Galvanised Steel
Application Method
Roller
Application Method
Brush
Components
1K
Usages
Pre-treatment
Product Type
Acid Etch
Fastest Delivery
Next Working Day
Colour Family
Grey
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send