We no longer stock this product, but can recommend Zinsser Allcoat Exterior Satin Water Based as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Mathys Fassilux Aqua XPE Satin is a water based, satin finish for interior and exterior timber and previously painted mineral substrates to provide a smooth, scratch resistant finish.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Mathys Fassilux Aqua XPE Satin
Mathys Fassilux Aqua XPE Satin is a water dilutable air-drying satin topcoat for interior and exterior works. Produces a scratch resistant satin finish on properly prepared wooden, or other already painted mineral substrates.
Features & Benefits
Technical Data
Drying Times At 20°C/RH 50%
Theoretical Consumption
Approx. 12 m²/l
Practical Consumption
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Surface Preparation
Application Conditions
10-30 degrees C. Relative humidity < 80%. Temperature of the substrate at least 3 degrees C above the dew point.
Remarks
If conventional spraying is used, the gloss might be somewhat lower.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Dorota on 2016-07-28 12:59:54 | Question: Hi there, I am using Mathys Fassilux Aqua XPE Satin - Colour: RAL1023 for painting wooden cupboard doors. The doors have been previously painted, so I sanded them down to roughen the surface for the paint to stick better, then applied Zinsser BIN shellac primer and then the Fassilux, as a thin layer (just one coat in places, two in others). A week on, and the paint still feels somewhat tacky. The same occurred on Zinsser BIN primed ply board - a week on, and still a bit tacky. Tacky to the extent that if you put one Fassilux painted surface touching another Fassilux painted surface, they stick to each other a bit. Is there anything I can do to speed up the drying process? Talcum powder? Some shelves I painted with Mathys Pegacryl Satin - Colour: RAL6027, same conditions, same time, happily accepted 2 coats, dried completely in 24 hours and are now done, whereas the Fassilux is still playing up... Thanks very much for your help! |
Answer from Rawlins’ Technical Team: Please refer to the Technical Data Sheet (TDS) for each product which can be downloaded from the 'DATASHEETS' tab on each respective product page on our website. Here it states that Mathys Fassilux Aqua XPE Satin should be touch dry in 3 hours, recoatable after 24 hours and full hardness will be achieved after 1 week. Mathys Pegacryl Satin is quicker drying at touch dry in 1 hour, recoatable in 24 hours and full hardness will be achieved after 2 days. All estimated drying times are based on 20°C and 50% r.h., low temperatures, lack of air flow and high relative humidity will prolong the drying/curing process. | |
Mathys Fassilux Aqua XPE Satin is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...
£12.04 (incl. VAT)
£10.03 (ex. VAT)
