A quick drying, one pack alkyd primer, Interprime 198 is surface tolerant, compatible with most substrates and can be overcoated with a wide range of finishes.
A quick drying, one pack alkyd primer, Interprime 198 is surface tolerant, compatible with most substrates and can be overcoated with a wide range of finishes.
For the maintenance of above water areas.
Approved for the carriage of grain when used as part of an approved scheme.
For use at Maintenance & Repair or On Board Maintenance.
| Colour | CPA097-White, CPA098-Grey, CPA099-Red |
| Finish/Sheen | Matt |
| Part B (Curing Agent) | Not applicable |
| Volume Solids | 41% ±2% (ISO 3233:1998) |
| Mix Ratio | Not applicable |
| Typical Film Thickness | 75 microns dry (183 microns wet) |
| Theoretical Coverage | 5.47 m²/litre at 75 microns dft, allow appropriate loss factors |
| Method of Application | Airless Spray, Brush, Roller |
| Flash Point (Typical) | Single Pack 35°C |
| Drying Information | -5°C | 5°C | 25°C | 35°C |
|---|---|---|---|---|
| Touch Dry [ISO 9117/3:2010] | 8 hrs | 3 hrs | 60 mins | 30 mins |
| Hard Dry [ISO 9117-1:2009] | 48 hrs | 24 hrs | 4 hrs | 2 hrs |
| Substrate Temperature | ||||||||
|---|---|---|---|---|---|---|---|---|
| -5°C | 5°C | 25°C | 35°C | |||||
| Interlac 665 | 24 hrs | 3 days | 6 hrs | 3 days | 2 hrs | 2 days | 60 mins | 24 hrs |
| Interprime 198 | 8 hrs | ext | 3 hrs | ext | 60 mins | ext | 30 mins | ext |
| Intersheen 579 | 24 hrs | 3 days | 24 hrs | 3 days | 12 hrs | 2 days | 6 hrs | 24 hrs |
| Interstores Alkyd | - | - | 6 hrs | 3 days | 2 hrs | 2 days | 60 mins | 24 hrs |
| Interstores Polyurethane | - | - | 24 hrs | 7 days | 12 hrs | 7 days | 6 hrs | 3 days |
| Interthane 990 | - | - | 24 hrs | 7 days | 12 hrs | 7 days | 6 hrs | 3 days |
| Intertherm 891 | 24 hrs | 28 days | 6 hrs | 28 days | 2 hrs | 28 days | 60 mins | 28 days |
See limitations.
VOC
Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
When used as part of an approved scheme, this material has the following certification:
Consult Rawlins Technical on 0113 2455450 (option 2) or send a message to [email protected] or your International Paint representative for details.
Approvals issued by external bodies may be dependent upon formulation and/ or manufacturing site.
Consult Rawlins Technical on 0113 2455450 (option 2) or send a message to [email protected] or your International Paint representative for the system best suited for the surfaces to be protected.
Use in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated should be clean, dry and free from contamination.
High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
Repair/OBM
Prepare area to be repaired to a minimum of St2 (ISO 8501-1:1998). Higher levels of surface preparation by abrasive blasting to Sa2 (ISO 8501-1:2001) or hydroblasting to HB2M (International Paint Hydroblasting Standards), will enhance product performance.
Feather or chip back surrounding area to a sound edge.
Ensure that the area is clean and dry prior to application of Interprime 198.
Overlap the primer onto existing coatings by approximately 2-3cm.
Consult Rawlins Technical or your International Paint representative for specific recommendations.
| Application | |
|---|---|
| Mixing | This material is a one pack coating and should always be mixed thoroughly with a power agitator before application. |
| Thinner | Not recommended. Use International GTA007 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. |
| Airless Spray | Recommended |
| Tip Range 0.53-0.66 mm (21-26 thou) | |
| Total output fluid pressure at spray tip not less than 176 kg/cm² (2500 p.s.i.) | |
| Conventional Spray | Application by conventional spray is not recommended. |
| Brush/Roller | Recommended. Multiple coats may be required to achieve specified dft. |
| Cleaner | International GTA007 |
| Work Stoppages and Cleanup | Thoroughly flush all equipment with International GTA007. All unused material should be stored in tightly closed containers. Partially filled containers may show surface skinning and/or a viscosity increase of the material after storage. Material should be filtered prior to use. |
| Welding | In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. |
It is recommended that Interprime 198 is not overcoated with epoxy coatings.
In certain regions, for specific customer requests and where cosmetic properties are not of concern, Interprime 198 may be applied without a cosmetic finish. Consult your regional technical centre for guidelines and details of colours available.
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of the data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.
Shelf life:
24 months minimum at 25°C. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
International Interprime 198 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
International Interlac 665 is a single component alkyd gloss enamel finish.Maintenance coating for use in a wide range of industrial environments including offshore, petrochemical and chemical plants Suitable for areas of limited chemical exposure where an economical single pack finish coat is required Cosmetic finish coat for alkyd...
£66.32 (incl. VAT)
£55.27 (ex. VAT)
A quick drying, one pack alkyd primer, Interprime 198 is surface tolerant, compatible with most substrates and can be overcoated with a wide range of finishes.For the maintenance of above water areas Approved for the carriage of grain when used as part of an approved scheme For use at Maintenance & Repair or On Board Maintenance...
£76.62 (incl. VAT)
£63.85 (ex. VAT)
International Intersheen 579 is a fast drying, single component, modified acrylic finish intended for use as a sealer coat for single pack acrylic intumescent coating systems but may also be used as a cosmetic finish over single pack primers and intermediates.4,800+ colours, inc. RAL, RAL Design & Effect, BS, NCS & the new NCS 2050...
£100.81 (incl. VAT)
£84.01 (ex. VAT)
International Interthane 990 is a two component acrylic polyurethane finish giving excellent durability and long term recoatability. Across the world, people are experiencing flexible application, extended recoat windows and reduced surface preparation costs with International Interthane 990 in both new construction and as a maintenance...
£130.20 (incl. VAT)
£108.50 (ex. VAT)
International Intertherm 891 is a one component, general purpose heat resistant paint for use as a heat resistant coating for general site use or as an industrial maintenance coating on both ambient and high temperature steelwork up to 315ºC (600ºF) where an economical aluminium finish is required. Coverage Calculator More Information...
£75.85 (incl. VAT)
£63.21 (ex. VAT)
International Interstores Alkyd Primer, a quick drying one pack primer that is surface tolerant and compatible with most substrates and able to be overcoated with a wide range of finishes. Use for the maintenance of above water areas and at On Board Maintenance only. Part of a dedicated range of On Board Maintenance (OBM) products specifically...
£69.42 (incl. VAT)
£57.85 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
