• Thermoguard Timbercoat BS Class 1/0 & EN Class B System Packs

Thermoguard Timbercoat BS Class 1/0 & EN Class B System

TC10B

We no longer stock this product, but can recommend Thermoguard Safewood Anti-Viral Fire Protection System as a great alternative.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
    Your customization:
Quantity

Description

We no longer stock this product, but can recommend Thermoguard Safewood Anti-Viral Fire Protection System as a great alternative.

Thermoguard Timbercoat BS Class 1/0 & EN Class B System - 4000+ colours available from RAL, BS & NCS

Thermoguard Timbercoat BS Class 1/0 & EN Class B System is a coloured fire retardant paint system for interior and exterior timber surfaces. These packs have been created to help users ensure they are purchasing sufficient product for their project. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Smoke & Flame Retardant Dualcoat) to ensure protection is achieved inline with the manufacturers recommendations to the respective area in question.

Each component of the packs can still be purchased individually if required here: Thermoguard Timbercoat and here: Thermoguard Smoke & Flame Retardant Dualcoat

Pack Contents

  • 20m² Pack (Interior Spec.) = 1 x 20m² Timbercoat + 1 x 20m² Smoke & Flame Retardant Dualcoat
  • 20m² Pack (Exterior Spec.) = 1 x 20m² Timbercoat + 2 x 20m² Smoke & Flame Retardant Dualcoat
  • 40m² Pack (Interior Spec.) = 2 x 20m² Timbercoat + 2 x 20m² Smoke & Flame Retardant Dualcoat
  • 40m² Pack (Exterior Spec.) = 2 x 20m² Timbercoat + 1 x 80m² Smoke & Flame Retardant Dualcoat
  • 80m² Pack (Interior Spec.) = 1 x 80m² Timbercoat + 1 x 80m² Smoke & Flame Retardant Dualcoat
  • 80m² Pack (Exterior Spec.) = 1 x 80m² Timbercoat + 2 x 80m² Smoke & Flame Retardant Dualcoat

Specification & Application
Prepare & apply according to manufacturer’s instructions

  • 1 coat of Thermoguard Timbercoat
  • 1 coat* of Thermoguard Smoke & Flame Retardant Dualcoat

*Apply 2 coats of Thermoguard Smoke & Flame Retardant Dualcoat for external, damp or high wear areas - Purchase 'Exterior Spec.' packs for this use. 2 coats may also be required for strong/dark colours - Thermoguard Timbercoat will be provided in a suitable undercoat shade to aid topcoat opacity unless instructed otherwise.

Please note: Timber must be clean and thoroughly dry prior to application (maximum 18% moisture content). Any gaps should be sealed with Thermoguard Intumescent Mastic. Fire should be prevented from accessing unprotected wood surfaces and for external applications it is recommended wood has been sealed on the reverse face to stop water ingress.

NOT suitable for the topside of floor surfaces that will be trafficked/walked on.

For 30 & 60 minute protection please see Thermoguard Timbercoat 30 & 60 Minute Protection System Packs.

For fire protection to doors, see Fire Door Upgrade Kits

Application to OSB/Sterling Board

This is a board made of chips of wood glued together to form a hard non-decorative board. If it needs fire coating, Thermoguard Fire Varnish or Timbercoat System can be applied to it. However we first recommend a test is carried out by applying a small amount of the proposed coating to the board to check for "cessing" / "cissing" (where coating gathers together in lumps and may leaving bare patches between). If this occurs the board should be degreased/cleaned and allowed to dry before testing again - if this still does not provide a satisfactory application please contact our Technical Team for further advice on 0113 2455450 (option 2) or send a message to [email protected].

UKAS Fire Test Standards

  • EN Class B s1 d0
  • BS Class 1 and Class 0

Project Fire Certification

We issue a Certificate of Supply on request for projects for insurance, Fire and Building Control Authority and Client Records.

Preparation

  • Surfaces should be free of contamination, sound, clean and dry.
  • Thoroughly abrade knotting, gloss, hard or smooth paints. Check adhesion of any existing coatings.
  • Unknown coatings or old fire coatings – contact our Technical Department on 0113 2455450.

Application Conditions

  • Apply to dry wood in dry conditions.
  • Max. timber moisture content 18%.
  • Max. relative humidity 70%.
  • Min. temp 5°C and 2°C above dewpoint.
  • Protect from rain until 1st coat of Thermoguard Smoke & Flame Retardant Dualcoat is dry.
  • Touch Dry: 4 hours / Overcoat: 6 hours
  • Ensure fully hard dry before next coat, only apply to dry timber in good drying conditions.

Spray equipment suggestions for Thermoguard Timbercoat and Thermoguard Smoke & Flame Retardant Dualcoat;

  • Pressure Pot & Gun conventional unit with small compressor
  • Ensure all traces of solvent flushed out
  • Thin 5 > 10% with water to spray viscosity
  • Adjust fluid flow & air flow as normal for acrylic emulsion paint

OR

  • Airless Graco 1500, 3500 or equivalent
  • 3/8” line, 30 mesh filter on machine, not filter in gun
  • 521 or 523, broad areas 621 or 623 tip

Ensure coverage is applied as per can - i.e. 20m² can covers 20m², 80m² can covers 80m², etc.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

Product Details
TC10B

Data sheet

Manufacturer
Thermoguard
Application Method
brush, roller, spray
Touch Dry
4 hours
Dry to Recoat
6 hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Adey on 2021-03-22 18:34:39
Question: 

Does this product come in clear?

Answer: 

No, but Thermoguard Fire Varnish BS Class 1/0 & EN Class B System is available in clear or translucent stained finishes and will achieve the same level of fire protection on suitable substrates.

questions Rakesh  on 2017-06-05 16:52:40
Question: Can you use the fire protective paint on treated timber.
Answer: 

Any pre-treatment should be free from wax or silicones. If caustic / high pH treatments used, neutralise wood pH before applying coatings. Ensure damp & fluid from wood treatment saturation fully dry out. Remove any loose surface deposits. If treatment left wood coated, contact our Technical Department with product information for further advice.


Question about the product

* Required fields
(read)
Send
You might also like

Thermoguard Timbercoat

Thermoguard Timbercoat is a durable fire protection paint for interior and exterior timber surfaces: Meets new Fire Regulations standard: BS EN Class B s1 d0, BS Class 1 Class O Surface Spread of Flame Can also achieve 30 & 60 minutes Fire Resistance in certain instances Expands to create a barrier, insulating wood from heat and...

Price £87.79
In stock

Thermoguard Timbercoat 60 Minute System

Thermoguard Timbercoat 60 Minute System is a coloured intumescent paint system for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Safewood Anti-Viral Smoke & Flame Retardant Topcoat) to ensure protection is achieved inline with the manufacturers recommendations to the...

Price £127.22 Regular price £141.36
In stock

Thermoguard Timbercoat Door Upgrade System

Thermoguard Timbercoat Door Upgrade System is an intumescent paint system to upgrade solid doors to 30min Fire Resistance and 30min Fire Doors to 60min: Available as a convenient pack containing the required basecoat and topcoat to protect 2 doors in a white or coloured Eggshell or Gloss finish Thermoguard UK will issue a Fire Certificate...

Price £125.88 Regular price £139.87
In stock