Rust-Oleum 5130 Primer DSP

    5130 2C

    We no longer stock this product, but can recommend Coo-Var Dampshield as a great alternative.

    Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

    Rust-Oleum 5130 Primer DSP is a super-high solids two pack epoxy resin primer designed for the suppression of vapour pressure effects.

    • Creates a barrier to stop rising moisture and vapour pressure
    • Prevents blistering
    • For use on asphalt and concrete
    • Very low solvent content
    • High build system

    Product not available
    This Product has been Discontinued


    Rust-Oleum 5130 Primer DSP

    Rust-Oleum 5130 Primer DSP is a super-high solids two pack epoxy resin primer designed for the suppression of vapour pressure effects to prevent air/moisture blistering on suspect concrete and asphalt balcony surfaces, suspended decking etc. prior to the application of a Rust-Oleum floor coating.

    • Creates a barrier to stop rising moisture and vapour pressure
    • Prevents blistering
    • For use on asphalt and concrete
    • Very low solvent content
    • High build system

    Technical Data

    • Density: 1,1
    • Gloss Level: Gloss
    • Solids content in volume: 96%
    • Mixing Ratio: Base : Activator = 1,7 : 0,8 (Volume)

    Drying Times At 20°C/RH 50%

    • Touch dry: 6 hours
    • Dry to handle: 16 hours
    • Dry to recoat: After 16 hours, but within 48 hours
    • Fully cured: 2 days
    • Pot Life: 30 minutes

    Theoretical Consumption


    Practical Consumption

    Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

    Surface Preparation

    Ensure surfaces are sound, clean, contaminant-free and as dry as possible before coating. Thoroughly scrub down all dirty surfaces with Rust-Oleum ND 14 (see PDS) alkaline detergent solution followed by thorough rinsing (alternatively steam clean) and dry off. Remove residual contamination by scraping, surface grinding etc. Mechanically remove any unsound/incompatible coatings. Fully grind bare concrete to give an open sandpaper like surface. Reduce undulations/peaks etc by mechanical abrasion or grinding. Remove laitance by acid cleaning and subsequent rinsing. Best results are obtained when blasting the floor. Repair holes or large cracks with Pegacrete or 5180 Epoxy Repair Mortar (see PDS for details).

    Application Conditions

    Minimum 10°C. Provide air ventilation: open windows and doors.

    Application Methods

    • Brush: Use undiluted.
    • Roller: Do not dilute. Use a 12-15 mm polyamide roller.
    • Rake/Trowl: Spread out the necessary material over the surface and distribute evenly using a rake or trowel. Use a spike roller if necessary to de-aerate coating


    Do not apply to inadequately prepared or unsound surfaces. Do not apply as surface temperatures below 10°C or overnight ambient temperatures below 5°C. Low overnight temperatures may further extend minimum overcoating times. Overcoating should be carried out within the timescales above to promote maximum intercoat adhesion and avoid film defects. Ensure surfaces are clean between coats.

    Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.

    Product Details
    5130 2C

    Data sheet

    Interior / Exterior Use
    Water / Solvent Based
    For Use On
    Concrete, Asphalt
    Application Method
    Brush, Roller
    Standard / Ready Mixed
    Single, Two or Three Pack
    Pack Size
    Mixing Ratio
    Base : Activator 1,7 : 0,8 (Volume)
    Brush, Roller
    Dry to Handle (at 20°C)
    16 Hours
    Dry to Recoat (at 20°C)
    After 16 hours, but within 48 hours
    Fully Cured (at 20°C)
    2 Days
    4m² per litre
    Recommended Thinner/Cleaner
    Rust-Oleum Thinner 160
    Min. Application Temperature
    Solids by Volume
    198 g/l
    Shelf Life (from date of manufacture)
    3 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
    Touch Dry
    6 Hours
    Recommended Dry Film Thickness
    240 µm
    Recommended Wet Film Thickness
    250 µm
    UN Number (Activator)
    UN Number (Base)

    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

    Be the first to ask a question about this product!

    Question about the product

    * Required fields


    Rust-Oleum 5130 Primer DSP is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT

    You might also like

    Rust-Oleum Thinner 160

    Rust-Oleum Thinner 160 is a specially formulated blend of solvents designed to mix with Rust-Oleum's 1085 Galva Zinc, 9100 High Performance Epoxy and B95 Flexible Epoxy to create an optimal consistency for application whether it be for Brush, Roller or Spray. Can also be used for the cleaning of some surfaces or equipment.Strong dilution...

    Price £18.15 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum Mathys ND14 Cleaner Degreaser

    Rust-Oleum Mathys Alkaline Cleaner/Degreaser ND14 should be used to remove grease, oil, proteins, dirt and many other surface contaminants from coated, mineral and steel substrates.Non-flammable, virtually odour-free cleaning/degreasing solution. Can be used as an additive for high pressure and steam cleaning Applied by synthetic sponge,...

    Price £74.82 (ex. VAT)
    In Stock and Available for Delivery

    General Painting Application Kit

    General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

    Price £8.02 (ex. VAT)
    In Stock and Available for Delivery

    Floor Application Kit

    Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.Each kit contains:12" Roller,...

    Price £75.24 (ex. VAT)
    In Stock and Available for Delivery