RSL Resucoat HB Profile

Resucoat HB Profile is discontinued and no longer available as a single product; please see RSL Resucoat HB and add RSL Resucoat Profile Aggregate.

Quantity
Product not available
This Product has been Discontinued

Description

Resucoat HB Profile is discontinued and no longer available as a single product; please see RSL Resucoat HB and add RSL Resucoat Profile Aggregate.

RSL Resucoat™ HB Profile is the perfect anti-slip component for any environment with potentially perilous flooring. Its gloss finish makes it aesthetically appealing, with several different colour options available.  

For any workplace that may have wet floors in winter or dirt being carried in, such as a showroom or food and beverage areas, Resucoat HB Profile is a low-maintenance, excellent anti-slip solution that can be cleaned with ease.

RECOMMENDED USES

  • Food processing and beverage areas
  • Showrooms
  • Chemical plant rooms
  • Engineering workshops
  • Automotive & aviation areas
  • Factory units
  • Warehouses
  • Demarcation and walkways

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resupatch.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where Resucoat Profile is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.

Priming

Open and porous substrates may require priming with Resuseal WB, also Resuprime NT or Resucoat HB may be used as primer on the dry substrates only, with less than 75% ERH reading.

Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of R.S.DAMPSHIELD at 200 microns per coat
85-92 2coats of R.S.DAMPSHIELD at 200 microns per coat
92-97 3coats of R.S.DAMPSHIELD at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of the base and hardener are removed from the buckets supplied. Mix using a slow speed electric mixer for 1-2 minutes and add the Resucoat Profile aggregate whilst mixing. Continue to mix for a further 1-2 minutes to ensure the aggregate is fully dispersed.

The mixed unit should be applied immediately by roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks.

Product Details

Data sheet

Application
Brush, Roller
Coverage
5kg will cover 17m sq. @ 200 microns wet film thickness.
Touch Dry
6 Hours
Brand
RSL
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuflor HB Standard Colours

Resuflor HB (formerly known as Resucoat HB) is a two-pack, high solids floor coating that utilises the latest epoxy resin technology to create a tough, protective and durable finish, ideal for both industrial and domestic environments. Standard colours - also available in RAL colours, with a 5-day lead time, separately here High-build...

Price £95.14 (ex. VAT)
In Stock and Available for Delivery

RSL Resuflor HB Profile Aggregate

RSL Resuflor HB Profile Aggregate (Formerly RSL Resucoat Profile Aggregate), pot to be added to a 5KG unit of RSL Resuflor HB to create a light textured, non-slip finish. More Information Delivery Info

Price £22.01 (ex. VAT)
In Stock and Available for Delivery