RSL Resutop LV

We no longer stock this product; contact our technical team on 0113 2455450 or [email protected] for a recommended alternative..

Quantity

Description

We no longer stock this product; contact our technical team on 0113 2455450 or [email protected] for a recommended alternative.

Resutop LV is the most chemically resistant resin of the Resutop range, for those industrial workplaces with dangerous goods that could be spilled on flooring. Whilst a bund is intended to catch spillage, Resutop LV takes away any risk of damaging the concrete floor and maintains uniformity.

It has exceptional resistance to abrasion, can be sterilised and its high-build coating is achievable in just one application, leaving a smooth gloss finish.

Recommended Uses

  • Areas with dangerous or volatile substances
  • Floors that are exposed to a high level of traffic
  • Engineering environments
  • Chemical plants
  • In conjunction with other Resin Surfaces Limited products

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resupatch or Resuscreed 45.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where Resutop LV is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.

Priming

Open and porous substrates may require priming with Resuseal WB, also Resuprime NT or Resucoat HB may be used as primer on the dry substrates only with a less than 75% ERH reading.

Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield should be specified and selected on the basis of hygrometer readings in accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of R.S.DAMPSHIELD at 200 microns per coat
85-92 2coats of R.S.DAMPSHIELD at 200 microns per coat
92-97 3coats of R.S.DAMPSHIELD at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.

The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.

 

Product Details
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resutop

Resutop is a two-pack, high solids, high-build epoxy coating, that creates an attractive chemical resistant heavy-duty industrial floor. ADVANTAGES High-build finish Hygienic and easily cleaned Good colour stability Smooth high gloss finish Low odour Hard wearing Anti-slip aggregate can be added Suitable for sterilising...

Price £65.90
In stock

RSL Resutop FH

Resutop FH is a fast curing, two-pack epoxy resin coating in one application that creates a seamless finish when chemical, abrasion, and impact resistance flooring is essential.  ADVANTAGES Recoat period of 4 hours at 20°C Non-toxic and solvent-free Good light reflection Good colour stability No shrinkage on curing Easy to clean...

Price £82.37
In stock