RSL Resubind UV

    RSBUB

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Quantity
    Product not available
    This Product has been Discontinued

    Description

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Resubind UV is a very versatile system for use both domestically and industrially. It can also be tailored to your requirements - choose your thickness and control the speed of the cure by adding the catalyst during mixing. 

    It has a low viscosity, has durable qualities, and can be used on a variety of decorative stones and aggregates.

    RECOMMENDED USES

    • Automotive showrooms
    • Sports grounds
    • Play areas with rubber crumb
    • Balconies, decks and hallways
    • Domestic driveways and walkways
    • Architectural features


    Resubind UV must be laid onto dry surfaces with a temperature of less than 7°C

    Preparation

    Internal New Floors: New concrete must be clean, sound and dry and fully cured with surface laitance removed, preferably by vacuum enclosed shot-blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required. For substrates with moisture reading above 75% ERH or above, considerations should be given to the use of R.S. Dampshield as a barrier coat. Resuprime NT may be used on substrate with less than 75% ERH moisture content.

    Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Surfaces must be thoroughly rinsed and dried before application of Resubind UV finishes.

    External Application: All surfaces must be clean, sound and dry at the time of application. Care must be taken to ensure that conditions remain suitable with no rain/condensation for the period of cure. The surface/substrate must be continuous and sound, and of a suitable composition to provide support to the laid surface.

    Priming

    Open and porous substrates may require priming with Resuprime NT, which may be used as primer on the dry substrates with less than 75% ERH reading.

    Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield should be specified and selected on the basis of hygrometer readings, in accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table:

    ERH% Required Coating Thickness
    75-85 1coat of R.S.DAMPSHIELD at 200 microns per coat
    85-92 2coats of R.S.DAMPSHIELD at 200 microns per coat
    92-97 3coats of R.S.DAMPSHIELD at 200 microns per coat

    For Further information please refer to recommended individual product data sheets.

    Application

    Ensure that all preparation and ground works are completed, and that a suitable surface remains that is both uniform in density and suitable for the application of the product. Edges/borders should be determined and any supporting battens fixed at the required height to allow for the correct placement of the mixed product.

    Only once the site is completely ready, should the base resin and hardener be mixed (Note: This provides a mixed base with a long pot life >8 hrs. On larger jobs the mixed resin can then be added to the mixer with the catalyst, for non-catalysed version and aggregate). The base resin mix, catalyst solution and washed dried aggregates can then be added to the forced action mixer and stirred, to thoroughly wet out the aggregate. Normally 1.5 kg of resin is added to 25kg of 2-5mm aggregate.

    Once mixed, the material should be placed swiftly and laid off by trowel, ensuring the product is well compacted and closed up on the surface.

    NB: The degree of closure of the surface is dependent on the nature, shape and grading of the aggregate, and is often open textured. No solvents should be added to this product. On extended applications, tools should be kept clean with R.S. Polyurethane Solvent.

    Product Details
    RSBUB

    Data sheet

    Application
    Trowel
    Coverage
    1.5 Kg to 25 Kg aggregate pack will cover 2m2 at 7mm thickness
    Touch Dry
    Once area is tack-free
    Brand
    RSL
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    RSL Resubind UV is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT