• RSL Resuscreed 55
    • RSL Resuscreed 55

    RSL Resuscreed 55

    SC55B

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Quantity
    Product not available
    This Product has been Discontinued

    Description

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Ordering References


    ColourNearest RAL MatchSizeFinishMimimum Order Quantity
    BlackRAL 901727.5KG or 55KGTextured10
    Flint GreyRAL 700527.5KG or 55KGTextured1
    Salsa RedRAL 301127.5KG or 55KGTextured10
    Stirling GreyRAL 700427.5KG or 55KGTextured10
    WhiteRAL 900327.5KG or 55KGTextured10
    Forest GreenRAL 600227.5KG or 55KGTextured10
    Kingfisher BlueRAL 501727.5KG or 55KGTextured10
    Poppy RedRAL 302027.5KG or 55KGTextured10
    Tuscan GreenRAL 601127.5KG or 55KGTextured10

    Please note that some products have minimum order quantities; these are made to order and may have extended lead times

    Resuscreed is more environmentally friendly than other seal coats due to the aggregate being free of crystalline silica. It is designed to produce an impervious finish. For best results, use in conjunction with R.S. Screed Seal by Resin Surfaces Limited (RSL).

    Recommended Uses

    • Pharmaceuticals
    • Engineering
    • Aerospace areas
    • Automotive industry
    • Chemical storage areas
    • Printing and packaging floors
    • Workshops
    • Schools
    • Supermarkets

    Preparation

    New concrete Floors: Must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue detergent is washed and removed by rinsing with clean water.

    Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability as it may not be compatible with existing floor coating.

    Where overcoating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets. The coating in each stage should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.

    Priming

    Open and porous substrates may require priming with Resuseal WB, also Resuprime NT may be used as primer on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

    The number of coats to be applied is chosen in accordance with the following table:

    ERH % Required Coating Thickness
    75-85 1 coat of Resuprime MVT at 200 microns per coat
    85-92 2 coats of Resuprime MVT at 200 microns per coat
    92-97 3 coats of Resuprime MVT at 200 microns per coat

    For further information please refer to recommended individual product data sheets.

    Application

    The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C to allow the ambient and substrate temperature to stabilise prior to installation.

    Mixing: Pre-mix the coloured base component to a uniform consistency (N.B. The base will appear gelled in the tin but will become fluid with mixing), then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Add the aggregate component slowly whilst mixing. Mix using an electric mixer for approximately two to three minutes until the three components have fully combined. For larger units a forced action mixer may be required to fully combine the aggregate into the resins.

    Resuscreed 55 should be worked with a trowel or float to achieve a dense, compacted finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down. Over-working the material will draw fines to the surface which may result in resin-rich spots and finish variations.

    Product Details
    SC55B

    Data sheet

    Application
    Trowel, Float.
    Coverage
    27.5Kg will cover 2.75 m sq. @ 5mm or 1.37 m sq. @ 10mm
    Touch Dry
    12-16 Hours
    Brand
    RSL
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    RSL Resuscreed 55 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    RSL Resuflor WB - Standard Readily Available Colours

    Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  These standard colours are readily available with faster shipping options; more colours are also available...

    Price £179.39 (ex. VAT)
    In Stock and Available for Delivery

    RSL Resuprime MVT

    RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on...

    Price £147.10 (ex. VAT)
    In Stock and Available for Delivery