RSL Elladur LM - Standard Readily Available Colours

ELLMB

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. See our Line Marking Paints page for more paints and coatings.

Quantity
Product not available
This Product has been Discontinued

100% secure payments
Description

RSL Elladur LM is a high-build Polyaspartic/Polyurea type fast-cure line marking floor coating based on advanced materials, designed to provide coloured tough and durable gloss finish in a range of thicknesses. Elladur™ LM is light stable with very good chemical resistance and can be applied to a variety of finishes and surfaces. Additional slip resistance can be created by incorporating suitable aggregates.

Recommended Uses

  • Where high-build UV stable coatings are required
  • Areas where fast turnaround but high performance finishes are required at low temperature.
  • Medical, Commercial and Industrial Floor areas
  • Decorative floors
  • Domestic areas

Advantages

  • Fast curing at low temperature
  • High build
  • UV stable
  • Very low odour
  • Tough but flexible
  • Can be applied onto a wide range of substrates
  • Can be used in commercial and industrial applications

Preparation

New Concrete Floors: New concrete must be clean, sound, dry and fully cured and surface laitance removed preferably by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded and surface must be primed prior to application.

Existing Concrete Floors: Remove all dirt, oil, grease old paints or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuflor Screed.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation, as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advise on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.

Where over-coating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated. These should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.

Where Elladur LM is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.

Priming

Elladur™ LM may be applied to an existing resin floor system, where a primer is not required. When applied direct to porous substrates such as concrete, the surface must be primed with Elladur™ SF Colour to ensure good adhesion to the surface.

Where the relative humidity of the substrate exceeds 75%, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
 85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

Application

Mixing: Pre-mix the base component to a uniform consistency, then add the entire contents of the hardener to the base and mix by using a slow speed electric mixer for approximately two minutes to achieve consistent mixture. Do not use a separate mixing bucket as it may affect the mixing ratio.

A rubber blade and/or a short-haired roller can work best for this application, to help avoid incorporating extra air and moisture in the coating. It is important to ensure that the recoat times are observed, with a maximum recoat of 8 hrs measured at 20°C substrate temperature and 50% relative humidity.

For other conditions please consult with our technical team. It is strongly recommended to apply the second coat as soon as the first coat has lost the tackiness to achieve the maximum adhesion. If the maximum recoating interval is exceeded, then the surface must be prepared and roughened to ensure intercoat adhesion.

Product Details
ELLMB

Data sheet

Application
Rubber blade, Roller.
Coverage
25 linear metres per 2.5kg unit @ 500 microns thickness and 100mm width.
Touch Dry
2-3 Hours
Brand
RSL
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuflor Screed

Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be...

Price £65.79
In Stock and Available for Delivery

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Easy application Use on...

Price £106.93
In Stock and Available for Delivery

RSL Resuflor Patch

RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum...

Price £35.96
In Stock and Available for Delivery