

We no longer stock this product, but can recommend Hitex PumaTrack Cycle Path and Walkway Paint as a potential alternative*.
*Please note: it is important to check that this alternative product is suitable for your requirements, please contact our Technical Team on 0113 2455450 (option 2) or send a message to [email protected] before purchasing to ensure this product would meet your project requirements.
Ennis-Flint MMAXGrip PRMX 45 is designed as a versatile MMA coating for application to bituminous substrates, possesses excellent abrasion-resistance and non-skid properties and was developed specifically as a heavy-duty surfacing and can be applied to asphalt substrates without a primer. The product is used as a priming surfacer, a topping layer and final course on external surfaces.
Ennis-Flint MMAXGRIP PRMX 45 is designed as a versatile MMA coating for application to bituminous substrates, possesses excellent abrasion-resistance and non-skid properties and was developed specifically as a heavy-duty surfacing and can be applied to asphalt substrates without a primer.
The product is used as a priming surfacer, a topping layer and final course on external surfaces that are subject to pedestrain and vehicular traffic, such as roads and plazas; furthermore, it is used for coloured road markings as well as for coating mastic flooring incorporating toppings. The surface can be of any colour and this coating can even be used to create patterns or car park markings and traffic guidance.
Features & Benefits
Areas of Application
Included in Pack
IMPORTANT: Ennis-Flint MMAXGRIP PRMX Catalyst MUST be purchased separately in order to use this product. The required quantity for the application conditions such be purchased accordingly (see below).
Reaction Times and Required amounts of Catalyst
Approx. | |
Pot life | 12 min. |
Rain-proof | 30 min. |
Walkable/Overlayable | 45 min. |
Fully cured | 2 hours |
Higher temperatures or greater proportions of catalyst will shorten reaction times, while lower temperatures and smaller proportions of catalyst will extend reaction times. The following table indicates the recommended amount of catalyst required to adjust the curing reaction to the temperature.
Substrate temperature in°C; required amounts of catalyst in % w/w (guide) | ||||||||||
Temperature | -5 | +3 | +5 | +10 | +15 | +20 | +25 | +30 | +35 | +40 |
MMAXGRIP PRMX Catalyst | 3% | 3% | 2% | 2% | 1.5% | 1.5% | 1.5% | 1% | 1% | 1% |
Application Equipment/Tools
For mixing the product:
- Twin-paddle stirrer
For applying the product:
- Rubber squeegee (45cm-60cm) or Smoothing trowel
Surface treatment with:
- Sheepskin roller/Textured Roller
Substrate Pre-treatment
MMAXGRIP PRMX 45 can be applied in top of a hardened layer of Primer. Primer is not required on asphalt surfaces.
Concrete
Ennis-Flint MMAXGRIP PRMX Primer is used as a primer on absorbent substrates, e.g. concrete. For further information, please refer to the technical information sheet.
Mixing
First stir the tub contents thoroughly. Then add the catalyst while stirring at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is incorporated. Ideally the roller-applied coating should therefore be re-potted once before stirring again. At product temperatures < 10˚C the product should be stirred for 4 minutes, as the catalyst will take longer to dissolve.
Application
Use a smoothing trowel or rubber squeegee to spread the material evenly and smooth it over, using the particle size as a guide to layer thickness. To achieve the desired finish, go over the area with a sheepskin or textured roller.
NOTE: Ennis-Flint MMAXGRIP PRMX 45 is subject to a 7 - 10 working day lead time. It is also available in all RAL colours, except effect colours. Please contact us for further details. Additional costs and extended lead times may be applicable.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Ennis-Flint MMAXGrip PRMX 45 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT