Bradite Epoxy Coating

EC88

We no longer stock this product, but can recommend Rust-Oleum 9100 High Solids Epoxy as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Bradite Epoxy Coating is a high performance, two-pack, solvent-based floor and general purpose epoxy coating for interior concrete, wood or steel floors requiring a tough, quick drying, hard wearing flexible floor coating with good chemical and excellent water resistance.

  • Available in more than 350 colours in RAL & BS
  • Ideally suited for the refurbishment of fibreglass swimming pools, having excellent water immersion & good chemical resistance and produces a surface that is easy to clean
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Quantity
Product not available
This Product has been Discontinued

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Available in more than 350 colours in RAL & BS
  • High performance, two-pack epoxy solvent-based floor and general purpose coating
  • Tough, quick drying, hard wearing and flexible
  • Good chemical and excellent water resistance
  • Produces a surface that is easy to clean
  • Can be used with Bradite Low Slip Additive LS30 to provide additional under foot traction
  • Ideally suited for the refurbishment of fibreglass swimming pools
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems



Preparation


For internal steel, wood, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence and have been properly prepared and primed. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Note: not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints.

Floor Preparation

  • Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. If the concrete is loose, chipping or has concrete dust present, the coating will not perform properly unless all loose material and dust is removed and damaged areas are repaired
  • Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch TA37, or primed using Bradite Floor Primer ES40
  • High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 Industrial Degreaser should be used if necessary to remove all grease and oil
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge
  • Cracks and pits should be filled using a suitable screed or mortar before painting

Fibreglass Swimming Pool Preparation

  • High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge
  • Bare fibreglass surfaces should be sweep blasted, mechanical or manually abraded to provide a key. The roughened surface should then be rinsed with clean water and allowed to thoroughly dry before painting

Industrial Protective Coating Preparation

  • High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface
  • Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil
  • For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically to SIS St 3 minimum)



Application


  • Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
  • Applicable by brush, roller, conventional air spray or airless spray:
    • Brush and Roller - Supplied ready for use. Thin, if required, with 0 - 10% Bradite Thinner TE36. On smooth substrates, the use of a short pile roller is advised
    • Conventional Air Spraying - Thin with 10 - 25% Bradite Thinner TE36 as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately
    • Airless Spraying - Thin with 0 - 20% Bradite Thinner TE36 as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately
  • For application on concrete, wood or other absorbent substrates, the first coat should be thinned 10-20% with Bradite Thinner TE36 to allow penetration into the substrate. If Bradite Floor Primer ES40 has been used then the priming coat of Bradite Epoxy Coating Finish EC88 should be omitted
  • For application on fibreglass swimming pools, the first coat is thinned 20% with Bradite Thinner TE36 to allow for better wetting and adhesion to the substrate. For maintenance painting the 1st coat will be a touch up to bare areas only
  • For additional underrfoot traction, Bradite Low Slip Hard Aggregate LS30 should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litre of paint
  • Clean all equipment immediately after use with Bradite Thinner TE36 for best results



Limitations


  • This system is recommended for internal protection and decoration only
  • Epoxy systems will chalk on external exposure to sunlight, resulting in loss of gloss and colour fade
  • Not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints
  • The end user and applicator must ensure that the finished floor is safe against slips in all likely usage conditions
  • Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label
Product Details
EC88

Data sheet

Manufacturer
Bradite
For Use By
Consumer Use
Interior / Exterior Use
Interior
Water / Solvent Based
Solvent
For Use On
Concrete, Wood, Steel
Application Method
Brush, Roller, Spray, Airless Spray
Sheen
Semi-Gloss
Colour
Fully, Tintable
VOC Levels
408 g/L
Single, Two or Three Pack
Two-Pack
Product Certifications
ISO 9001:2008, ISO 14001:2004
Pack Size
5L
Application
Brush, Roller, Spray
Dry to Recoat (at 20°C)
14 hours - 6 days
Pot Life (at 20°C)
2 - 3 hours
Coverage
11m2 per Litre
Recommended Thinner/Cleaner
Bradite Thinner TE36
Density
1.41 kg/L
Solids by Volume
52% (mixed)
Touch Dry
3 Hours
Recommended Wet Film Thickness
100 microns/coat
UN Number (Activator)
UN1263
UN Number (Base)
UN1263
Flashpoint
(Abel closed cup) 27°C
Colour(s)
Fully Tintable
Base Type
Solvent-Based
Exterior / Interior Use
Interior Use
Suitable For Use On
Concrete
Suitable For Use On
Steel
Suitable For Use On
Wood
Finish
Semi-Gloss
Application Method
Roller
Application Method
Brush
Application Method
Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Bradite Epoxy Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like

Bradite Floor Primer

We no longer stock this product, but can recommend Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...

In stock

Bradite Acid Etch

Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete. Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...

Price £24.18 (ex. VAT)
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28 (ex. VAT)
In Stock and Available for Delivery

Bradite TE36 Epoxy Thinner

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Bradite TE36 Epoxy Thinner is a high flash point solvent for thinning epoxy paints and equipment cleaning. Manufactured under the auspices of an...

In stock

Bradite Low Slip Additive (LS30)

Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use. Manufactured under the auspices of an ISO 9001:2008...

Price £10.27 (ex. VAT)
In Stock and Available for Delivery