Bradite Roadline Paint

CR27

We no longer stock this product, but can recommend Bradite Floor-It as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Quantity
Product not available
Temporarily Out of Stock

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Quick drying universal line marking paint
  • For internal & external asphalt, steel, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared
  • Applicable by brush, roller, conventional air spray, or airless spray
  • Surface dry in just 10 minutes
  • Can be used with Bradite Low Slip Additive LS30 to provide additional under foot traction
  • Reflectivity can be achieved by using proprietary glass beads
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems



Application Notes


  • Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details
  • High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite Industrial Degreaser industrial strength detergent should be used if necessary to remove all grease and oil
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting
  • Mix thoroughly before use. Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
  • Brush and Roller - Supplied ready for use. Thin, if required, with 0 - 5% Bradite Line Marking Paint Thinner TB34
  • Conventional Air Spraying - Thin with 10 - 20% Bradite Thinner TB34 as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately
  • Airless Spraying - Thin with 0 - 15% Bradite Thinner TB34 as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately
  • To provide additional under foot traction, Bradite Low Slip Hard Aggregate LS30 should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litre of paint
  • For application on concrete or other absorbent substrates, the first coat should be thinned 15-20% with Bradite Thinner TB34 to allow penetration into the substrate.
  • For maintenance painting the 1st coat will be a touch up to bare areas.
  • While the coating will take light foot traffic after overnight drying, full cure may take 4 days at 20⁰C, and should not be subject to heavy traffic for at least 24 hours.

Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity.



Product Details
CR27

Data sheet

Manufacturer
Bradite
For Use By
Professional Use
Interior / Exterior Use
Interior and Exterior
Water / Solvent Based
Solvent
For Use On
Asphalt, Steel, Concrete, Mineral Substrates
Application Method
Brush, Roller, Airless Spray Conventional, Air Spray
Sheen
Eggshell
Colour
Standard / Ready Mixed, Fully Tintable
Single, Two or Three Pack
Single
Product Certifications
ISO 9001:2008, ISO 14001:2004 environmental management systems
Pack Size
5L
Fully Cured (at 20°C)
4 days
Coverage
5 m2 /L/coat
Recommended Thinner/Cleaner
Bradite Thinner TB34 (clean with Bradite Thinner TC32)
Min. Application Temperature
Down to -5°C (but must be 3°C above dew point)
Density
1.58 kg/L
Solids by Volume
50%
VOC
430 g/l
Touch Dry
10 Mins
Recommended Dry Film Thickness
100 microns/coat
Recommended Wet Film Thickness
200 microns/coat
UN Number
UN1263
Colour(s)
Fully Tintable
Base Type
Solvent-Based
Exterior / Interior Use
Exterior & Interior Use
Suitable For Use On
Steel
Suitable For Use On
Concrete
Suitable For Use On
Asphalt
Finish
Eggshell
Application Method
Roller
Application Method
Brush
Application Method
Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Nick Parsons on 2021-04-07 17:45:38
Question: 

Hi, will this paint be useful on grids / manhole covers made of metal and be hard wearing against fork lift truck traffic?

Answer from Rawlins’ Technical Team: 

Assuming the manhole covers are bare, clean, dry, sound and prepared as detailed in the technical data sheet this can be used.

questions Mike chapman on 2019-09-20 12:03:09
Question: 

Can this product be applied to newly laid HRA please?

Answer from Rawlins’ Technical Team: 

Yes as long as it has cooled for at least a period of 48 hours.


Question about the product

* Required fields
(read)
Send
You might also like

Bradite Floor Primer

We no longer stock this product, but can recommend Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...

In stock

Bradite Acid Etch

Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete. Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...

Price £24.18 (ex. VAT)
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28 (ex. VAT)
In Stock and Available for Delivery

Bradite TB34 Line Marking Paint Thinner

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Bradite TB34 Line Marking Paint Thinner is a low flash point solvent to thin etching primers, select chlorinated rubber paints and for equipment...

In stock

Bradite Low Slip Additive (LS30)

Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use. Manufactured under the auspices of an ISO 9001:2008...

Price £10.27 (ex. VAT)
In Stock and Available for Delivery