Bradite Rapid

PW74

We no longer stock this product, but can recommend Smartkote Safekote as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Bradite Rapid is a high performance single-pack moisture cure polyurethane floor coating that is ideal for commercial and industrial environments. Available in a large amount of colours, including RAL shades, the tough and flexible film will provide water and chemical resistance. 

  • Available in more than 350 colours in RAL & BS
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems

Please note: This product is intended for professional use only. Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Quantity
Product not available
This Product has been Discontinued

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Good chemical and water resistance
  • For industrial and commercial environments
  • Produces a tough flexible film
  • Hard-wearing
  • Dries quick
  • Ideal for use as a floor sealer
  • Suitable for forklift traffic (after 48hrs)
  • Can be used with Bradite Low Slip Additives LS30 to provide additional under foot traction
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems



Preparation


  • For internal steel, wood, concrete and other absorbent mineral substrates which are free of contamination, dust, efflorescence and have been properly prepared and primed
  • Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, acid etched using Bradite Acid Etch TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details
  • High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting. Substrate should be dust free and completely dry before coating



Application


  • Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
  • Clean all equipment immediately after use with Bradite Thinner TP33 for best results
  • For application on concrete, wood or other absorbent substrates, the first coat should be thinned 10-20% with Bradite Thinner TP33 to allow penetration into the substrate
  • For maintenance painting, the 1st coat will be a touch up to bare areas only. While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20⁰C, and should not be subject to heavy traffic for at least 48 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity
  • Theoretical coverage: 10 m2/L/coat @ 69 microns/coat DFT/100 microns/coat WFT
  • Surface dry in 2 hours, recoat in 8 - 16 hours (after 16 hrs, coating should be abraded)
  • While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20°C, and should not be subject to heavy traffic for at least 48 hours
  • For additional under foot traction, Bradite Low Slip Hard Aggregate LS30 should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litre of paint



Limitations


  • This product is intended for professional use only
  • Compatibility with existing coatings should be confirmed by preparing and painting a test patch
  • Not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints
  • Drying/curing times will vary depending on film thickness, temperature and relative humidity
  • Due to the rapid drying of Bradite Rapid PW74 it is advised that once opened the can should not be resealed
  • Hot high performance or new tyres may cause slight discolouration of very new coatings at the point of contact. This effect is very rare but may be noticeable in light colours and is due to the migration of rubber compounding materials into the surface of the coating
  • As with all aromatic moisture cure prepolymers, direct exposure to sunlight will cause yellowing. This effect will be most noticeable in light colours and the degree of yellowing will be in proportion to the amount of direct sunlight exposure
Product Details
PW74

Data sheet

Manufacturer
Bradite
For Use By
Professional Use
Interior / Exterior Use
Internal
For Use On
Steel, Wood, Concrete
Application Method
Brush, Roller, Spray
Sheen
Gloss
Colour
Fully Tintable
VOC Levels
276 g/L
Single, Two or Three Pack
Single
Pack Size
4.5L
Application
Brush, Roller
Dry to Recoat (at 20°C)
8 - 16 hours
Fully Cured (at 20°C)
7 days
Coverage
10m2 per Litre
Recommended Thinner/Cleaner
Bradite Thinner TP33
Min. Application Temperature
Down to -5°C (but must be 3°C above dew point)
Density
1.07 kg/L
Solids by Volume
69%
Shelf Life (from date of manufacture)
6 months minimum in original unopened containers
Touch Dry
2 Hours
Recommended Dry Film Thickness
69 microns/coat
Recommended Wet Film Thickness
100 microns/coat
UN Number
UN1263
Dry for Light Traffic (at 20°C)
24 hours minimum, after final coat
Flashpoint
(Abel closed cup) 26°C
Colour(s)
Standard Colours
Base Type
Solvent-Based
Exterior / Interior Use
Interior Use
Suitable For Use On
Concrete
Suitable For Use On
Steel
Suitable For Use On
Wood
Finish
Gloss
Application Method
Brush
Application Method
Spray
Application Method
Roller
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Bradite Rapid is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like

Bradite Floor Primer

We no longer stock this product, but can recommend Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...

In stock

Bradite Acid Etch

Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete. Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...

Price £24.18 (ex. VAT)
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28 (ex. VAT)
In Stock and Available for Delivery

Bradite TP33 Polyurethane Thinner

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Bradite TP33 Polyurethane Thinner is a high flash point solvent for thinning two pack polyurethane paints and equipment cleaning. Manufactured...

In stock

Bradite Low Slip Additive (LS30)

Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use. Manufactured under the auspices of an ISO 9001:2008...

Price £10.27 (ex. VAT)
In Stock and Available for Delivery