Bradite Chlorinated Rubber

CG23 / CC24

We no longer stock this product, but can recommend Teamac Chlorvar Chlorinated Rubber Paint as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Bradite Chlorinated Rubber is a high performance single pack chlorinated rubber gloss/eggshell finish with excellent chemical & water resistance for use on concrete, porous mineral and suitably prepared ferrous and non-ferrous surfaces.

  • Available in over 350+ colours in RAL and BS
  • Quick drying coating with excellent water and good chemical resistance, suitable for concrete swimming pools
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Quantity
Product not available
This Product has been Discontinued

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Available in over 350+ colours in RAL and BS
  • High performance single pack chlorinated rubber gloss/eggshell finish
  • Excellent water and good chemical resistance
  • For use on concrete, porous mineral and suitably prepared ferrous and non-ferrous surfaces
  • Suitable for use on concreteswimming pools
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems



Preparation


  • For ferrous and non-ferrous metals, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared
  • Substrate should be dust free and completely dry before coating
  • When painting new concrete it is vital to ensure the substrate is fully cured and free of laitance. Power floated, shiny or unpainted non porous concrete should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch TA37
  • High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate. For best performance, complete vacuum blast cleaning of the substrate is recommended
  • Bradite TD39 Industrial Degreaser washing and rinsing should be used with scrubbing to remove grease or oil
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge
  • Cracks and pits should be filled using a suitable screed or mortar before painting
  • Galvanised steel, aluminium and other non-ferrous metal substrates should be roughened by mechanical abrading or sweep blasting with inert grit. Steel should be blast cleaned to SIS-Sa 2½ minimum, blast profile 35-50 microns and surface free of soluble salts, or de-rusted manually or mechanically to SIS-St 3 minimum



Application


  • Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
  • Applicable by brush, roller, conventional air spray or airless spray:
    • Brush and Roller - Thin with 0 - 5% Bradite Thinner TC32 as required. Short pile “Mohair” sleeve preferred for best appearance
    • Conventional Air Spraying - Thin with 5 - 15% Bradite Thinner TC32 as required, tip size – 2.0 mm, tip pressure 60psi (0.4MPa) approximately
    • Airless Spraying - Thin with 0 - 10% Bradite Thinner TC32 as required, tip size - 13 thou (0.33mm) approximately, tip pressure - 2100 psi (15MPa) approximately
  • For application on concrete or other absorbent substrates, the first coat should be thinned 15-20% with Bradite Thinner TC32 to allow penetration into the substrate. For maintenance painting the 1st coat will be a touch up to bare areas
  • For application on industrial new build and maintenance, apply three coats Bradite Chlorinated Rubber Eggshell CC24. For a gloss finish, substitute final coat with Bradite Chlorinated Rubber Gloss CG23. For maintenance, the first coat will be spot priming exposed substrate only
  • Clean all equipment immediately after use with Bradite Thinner TC32 for best results



Limitations


  • For well-constructed pools, particularly those with an external waterproof membrane, best results are obtained with Bradite Chlorinated Rubber Gloss CG23
  • Where the site has a high water table and the pool is constructed without waterproof barrier, the higher porosity Bradite Chlorinated Rubber Eggshell CC24 is preferred since this material will minimise blistering due to external water pressure when the pool is empty
  • Painted pools should be left to thoroughly dry before filling. In temperate climates, assuming good ventilation and air movement, this will take approximately 10 days from final coat application
  • Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Unsuitable for epoxy tar & bitumen paints, Portland cement, marble & tiled surfaces
  • Drying/curing times will vary depending on film thickness, temperature and relative humidity
  • Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label



Product Details
CG23 / CC24

Data sheet

For Use By
Professional Use
For Use On
Concrete, Steel
Application Method
Brush, Roller, Spray
Sheen
Gloss, Eggshell
Colour
Fully Tintable
VOC Levels
548g/L (Gloss) 524g/L (Eggshell)
Single, Two or Three Pack
Single
Pack Size
5L
Coverage
12m2 per Litre (Gloss) 10m2 /L/coat (Eggshell)
Recommended Thinner/Cleaner
Bradite Thinner TC32
Density
1.29 kg/L (Gloss) 1.42 kg/L (Eggshell)
Solids by Volume
45%
Touch Dry
30 Mins
Recommended Wet Film Thickness
84 microns/coat (Gloss) 100 microns/coat (Eggshell)
Flashpoint
(Abel closed cup) 38°C
Colour(s)
Fully Tintable
Base Type
Solvent-Based
Exterior / Interior Use
Exterior & Interior Use
Suitable For Use On
Steel
Suitable For Use On
Non-Ferrous Metals
Suitable For Use On
Concrete
Suitable For Use On
Ferrous Metals
Finish
Eggshell
Finish
Gloss
Application Method
Brush
Application Method
Spray
Application Method
Roller
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Bradite Chlorinated Rubber is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like

Bradite Acid Etch

Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete. Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...

Price £24.18 (ex. VAT)
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28 (ex. VAT)
In Stock and Available for Delivery

Bradite TC32 Chlorinated Rubber/Pliolite Thinner

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Bradite TC32 Chlorinated Rubber/Pliolite Thinner is a high flash point aromatic solvent for thinning alkyd based paints and equipment cleaning....

In stock

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22 (ex. VAT)
In Stock and Available for Delivery