Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Bradite Fastrac GP Anti-Corrosive Primer is a fast drying modified alkyd anticorrosive primer intended for use as a general use fast drying prefabrication or system primer on properly prepared ferrous surfaces.
Ideal for ferrous surfaces and suitable for coating over compatible coatings, including under many Bradite finishes such as Fastrac
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
Light surface rusting may be effectively treated using one coat of Bradite Fastrac Rust Converter RC46 prior to application of Bradite Fastrac GP Anticorrosive Primer AP70
New galvanised steel should be thoroughly degreased and then pre-treated with Bradite Mordant Solution TM38 prior to application of Bradite Fastrac GP Anticorrosive Primer AP70. Alternatively, or for other nonferrous metals, prime with Bradite Barrier Primer EU96 before application of selected Bradite finish.
For ferrous surfaces blast cleaned to SIS Sa 21/2 minimum or mechanically prepared to SIS St 3 minimum.
Suitable for coating over compatible coatings which are clean, dry and abraded
Suitable for use under many Bradite finishes such as Fastrac
High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 Industrial Degreaser, washing and rinsing should be used with scrubbing to remove grease or oil
Remove all rust scale, loose mill scale or other corrosion products by scraping and mechanical cleaning to SIS-St 3 (ISO 8501-1:1998)
Intact areas of existing coatings should be roughened by abrasive manual or disc sanding, feathering back to a sound coating edge. Cracks and pits should be filled using a suitable metal filler before painting. Substrate should be dust free and completely dry before coating
Application
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
Applicable by brush, roller, conventional air spray or airless spray:
Brush and Roller - Supplied ready for use. Thin with 0 - 5% Bradite Thinner TW35 if required
Conventional Air Spraying - Thin with 10 - 20% Bradite Thinner TW35 as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately
Airless Spraying - Thin with 0 - 15% Bradite Thinner TW35 as required, tip size - 19 thou (0.48mm) approximately, tip pressure - 2100 psi (15MPa) approximately.
Apply 1 - 2 full coats at 58 microns/coat WFT or 35 microns/coat DFT
Theoretical coverage 9 m2/L/coat
Clean all equipment immediately after use with Bradite Thinner TW35 for best results
Touch dry in 1 hour, recoat after 16 hours+, fully cured in 7 days
Product Details
AP70
Data sheet
Manufacturer
Bradite
For Use By
Consumer Use
Water / Solvent Based
Solvent
For Use On
Ferrous Metals
Application Method
Airless Spray, Conventional Air Spray, Brush, Roller
Sheen
Flat
Colour
Standard / Ready Mixed
VOC Levels
320 g/L
Single, Two or Three Pack
Single
Product Certifications
ISO 9001:2008, ISO 14001:2004 environmental management systems
Pack Size
5L
Dry to Recoat (at 20°C)
16 hours - unlimited
Fully Cured (at 20°C)
7 days
Coverage
12m2 per Litre
Recommended Thinner/Cleaner
Bradite Thinner TW35
Min. Application Temperature
Down to 5°C & 60% RH maximum (but must be 3°C above dew point)
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Bradite Fastrac GP Anti-Corrosive Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
A highly refined solvent meeting the requirements of BS245.
Suitable for general cleaning purposes, brush cleaning and paint thinning.
More suitable for paint thinning than other solvents as it will not affect the drying time of oil based paints
More Information Delivery Info
We no longer stock this product, but can recommend Rust-Oleum CombiColor Original as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113...
We no longer stock this product, but can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...
Bradite Fastrac Rust Converter is a high performance, single-pack, water-based rust converter intended for the treatment and passivation of surface rust on all hand or mechanically prepared rusty ferrous surfaces.
Especially suited for objects which may be difficult to sand blast such as; fences, iron railings, guttering and outdoor...
Teamac High Performance 2 Pack Zinc Phosphate Primer (also known as Teamac High Performance Marine Primer Undercoat, and formerly High Performance Marine Primer) is a two-pack epoxy zinc phosphate coating that offers the highest level of corrosion resistance for above and below the waterline in harsh marine environments.
Suitable for...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...