• Bradite Surface Tolerant Primer

Bradite Surface Tolerant Primer

EP92

We no longer stock this product, but can recommend Tikkurila Temabond ST 200 as a great alternative.

Quantity
Product not available
This Product has been Discontinued

Description

We no longer stock this product, but can recommend Tikkurila Temabond ST 200 as a great alternative.

Bradite Surface Tolerant Primer is a high performance epoxy solvent-based surface tolerant anti-corrosive primer capable of being applied over lightly rusted ferrous surfaces, such as:

  • Fences
  • Gates
  • Lightly-rusted Shipping containers
  • Factory

Ideally suited for surfaces and structures on which thorough blast cleaning may not be feasible or practical.

Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/j sb): 500g/l (2010). This product contains max. 373 g/l VOC.


Features & Benefits

  • Polymide adduct cured primer for steel.
  • Contains a high level of zinc phosphate anti-corrosive pigment.
  • Forms a tough and hard-wearing film.
  • Flexible and abrasion resistant.
  • Will cure in low temperatures, even down to 0°C.
  • Conforms with parts CP5C of BS5493.
  • Two-pack epoxy system.
  • Eggshell sheen.


Preparation

Industrial protective coating

High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.

For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically abraded to SIS St 3 minimum).

1st coat: Bradite Surface Tolerant Epoxy Primer EP92.

2nd coat: Bradite HB MIO Epoxy Build Finish EM97.

3rd coat: Bradite Polyurethane Gloss Finish PG77.

4th coat: Bradite Polyurethane Gloss Finish PG77.

Wet blasted steel

High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.

Steel should be wet blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns then rinsed with fresh water, with excess water being blown off with oil free compressed air. (For maintenance repair, wet blast as previous, feather existing coating to a sound edge and abrade to provide a key.)

1st coat: Bradite Surface Tolerant Epoxy Primer EP92.

2nd coat: Bradite HB MIO Epoxy Build Finish EM97.

3rd coat: Bradite Polyurethane Gloss Finish PG77.

In all cases, an induction period of 20 minutes after mixing is required if material temperatures are below 10oC. For maintenance painting, the 1st coat will be a touch up to bare areas only.


Application

Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Brush and Roller: supplied ready for use. Thin, if required, with 0-10% Bradite Thinner TE36.

Conventional Air Spraying: Thin with 10-20% Bradite Thinner TE36 as required, tip size - 3.0mm, tip pressure 60psi (0.4MPa) approximately.

Airless Spraying: Thin with 0-15% Bradite Thinner TE36 as required, tip size - 19 thou (0.48mm) approximately, tip pressure - 2100 psi (15MPa) approximately.

Clean all equipment immediately after use with Bradite Thinner TE36 for best results. Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.

Product Details
EP92

Data sheet

Manufacturer
Bradite
Water / Solvent Based
Solvent
Application Method
Conventional Air Spray, Airless Spray, Brush, Roller
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Product Certifications
SO 9001:2008, ISO 14001:2004 environmental management systems
Pack Size
5L
Coverage
7.5m2 per Litre
Touch Dry
2 Hours
UN Number
UN1263
Brand
Bradite
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Bradite Surface Tolerant Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT