

We no longer stock this product, but can recommend Bradite Chlorinated Rubber as a great alternative.
We no longer stock this product, but can recommend Bradite Chlorinated Rubber as a great alternative.
Bradite CR Anti-Corrosive Primer is a high performance single pack chlorinated rubber anti-corrosive primer with excellent chemical & water resistance. A quick drying primer, for use on suitably prepared ferrous surfaces such as fences, gates, shipping containers, etc.
Additionally, this primer may be used to prime ferrous metalwork within factories, industrial outlets and production plants, such as: automotive production lines, industrial laundry and commercial sewing factory.
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.
Substrate should be dust free and completely dry before coating.
High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate. For best performance, complete vacuum blast cleaning of the substrate is recommended. Bradite TD39 industrial strength detergent washing and rinsing should be used with scrubbing to remove grease or oil.
Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.
Steel should be blast cleaned to SIS-Sa 2½ minimum, blast profile 35-50 microns and surface free of soluble salts, or de-rusted manually or mechanically to SIS-St 3 minimum.
Painting System - Industrial New Build & Maintenance
1st coat: Bradite Chlorinated Rubber Eggshell CP26.
2nd coat: Bradite Chlorinated Rubber Eggshell CC24.
3rd coat: Bradite Chlorinated Rubber Eggshell CC24 - for a gloss finish, substitute final coat with Bradite Chlorinated Rubber Gloss CG23.
For galvanised steel and other non-ferrous surfaces, the first coat should be substituted with Bradite Barrier Primer EU96. For maintenance, the first coat will be spot priming exposed substrate only.
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
Brush and Roller: Thin with 0-5% Bradite Thinner TC32 as required.
Conventional Air Spraying: Thin with 10-20% Bradite Thinner TC32 as required, tip size – 2.0 mm, tip pressure 60psi (0.4MPa) approximately.
Airless Spraying: Thin with 5-10% Bradite Thinner TC32 as required, tip size - 23 thou (0.58mm) approximately, tip pressure - 2100 psi (15MPa) approximately.
Clean all equipment immediately after use with Bradite thinner TC32 for best results. Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.