Carboline Carboguard 635 VOC is an all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. It has low VOC and low HAP's content for use in areas with restricted volatile emissions.

Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure for handling. May also be used for immersion in potable water, fresh or salt water (marine) exposures.

Click To Jump To Section:

• Features and Benefits
• Product Specification
• Drying Times
• Surface Preparation
• Application Methods
• Application Conditions
• Health and Safety

Features and Benefits

• Low temperature cure (20°F)
• Excellent corrosion protection
• Excellent application characteristics
• Fast recoat times
• Moisture tolerance during application
• Extended recoat window for atmospheric exposures (6 months for most topcoats)
• Low VOC and low HAPs content
• Satin finish

Product Specification

Drying Times

These times are to be used as a guideline for non-immersion applications.

• The longer the first coat has to cure, particularly in sunlight exposure or elevated temps, the higher risk of inadequate adhesion. If the maximum recoat times have been exceeded, the surface must be abraded by sweep blasting or sanding prior to the application of additional coats.
• The listed times in the chart above are based on a 4-6 mil (100-150 micron) dry film thickness per coat. Deviation from those thicknesses may compromise the performance and adhesive properties of the film. Higher film thickness, insufficient ventilation or cooler temperatures could result in solvent entrapment and premature failure.
• Excessive humidity or condensation on the surface during curing will not affect performance but may cause discoloration and result in a surface haze. Any haze or blush must be removed by water washing before recoating.
• Recoat intervals may vary from those listed above when using under intumescent fireproofing products.
• Contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected] for recommended cure times before applying Carboline intumescent products.
• If the maximum recoat times have been exceeded, the surface must be abraded by sweep blasting or sanding prior to the application of additional coats.
• For force curing, contact Rawlins for specific requirements.
• Do not apply to substrates with ice or ice crystal formation.
• Dehumidify or raise the temperature to eliminate ice on the substrate.
• This product will tolerate drops in temperature to 0°F (-17°C) during its cure and will continue to cure when the temperature rises.

Cure for Potable Water Use

• 7-day cure after final coat @ 75°F

The curing schedule above references curing times for immersion service when an antifoulant topcoat is used.

• The optimum time to topcoat with an antifoulant is when the film is "touch-tacky." If the touch-tacky time has been exceeded, or if the film is "glossy," you can generally re-prime/refresh the first coat with a fresh coat of itself. High temps and/or sunlight exposure may shorten this recoat schedule.

Marine Use

• Undocking time of 24 hours @75°F

Surface Preparation

General

• Remove any oil or grease from surface to be coated with clean rags soaked in Carboline Thinner #2 or toluol.

Steel

• Atmospheric Exposure: For optimal performance: Hand Tool or Power Tool clean in accordance with SSPC-SP 2, SSPC-SP 3, or SSPC-SP11 to produce a rust-scale free surface. For maximum performance: SSPC-SP 6 (or greater) with a 1½-3 mil (40-75 micron) blast profile
• Immersion Service: Minimum near white metal cleanliness in accordance with SSPC-SP10

Galvanised Steel

• Galvanizing requires a roughened surface for optimum adhesion/performance of high build epoxies.
• Remove any contaminants per SSPC-SP1; ensure there are no chemical treatments that may interfere with adhesion; and abrade the surface to establish a suitable roughness (typically 1 mil). SSPC-SP16 or SSPC-SP7 are acceptable methods.

Concrete or CMU

• Remove all loose, unsound concrete. Remove all oils or other non-compatible sealers or treatments.
• Do not apply coating unless the concrete has cured at least 28 days @ 70 F (21 C) and 50% relative humidity or equivalent.

Stainless Steel

• Surface profile should be a dense angular 1-3 mils and is best achieved through abrasive blasting in accordance with SSPC-SP16.
• Remove all contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, embedded iron or chlorides.

Application Methods

Application Conditions

• Industry standards are for substrate temperatures to be above the dew point.
• Carboguard 635 is unique in that it can tolerate damp substrates.
• Special application techniques may be required above or below normal application conditions.
• Special thinning and application techniques may be required above or below normal conditions.

Health and Safety

Clean Up

• Use Carboline Thinner 2 or MEK.
• In case of spillage, absorb and dispose of in accordance with local applicable regulations.

Safety

• Read and follow all caution statements on this product data sheet and on the SDS for this product.
• Wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.

Ventilation

• When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
• The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used.
• User should test and monitor exposure levels to ensure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator.

Caution

• This product contains flammable solvents
• Keep away from sparks and open flames
• All electrical equipment and installations should be made and grounded in accordance with applicable regulations.
• In areas where explosion hazards exist, workmen should be required to use nonferrous tools and wear conductive and non-sparking shoes.

• Refer to the product and safety data sheet in the attachments section above for further details.