We no longer stock this product, but can recommend Carboline Carboguard 891 VOC as a great alternative.
Carboline Carboguard 891 FC is a two-component, high solids and fast epoxy topcoat. This coating is a high build mixture and provides excellent corrosion protection. Available in RAL shades, Carboline Carboguard 891 FC is an ideal topcoat for many applications, including hydro-power, offshore, chemical processing, and other heavy industry.
| Technical Data | ||||||
|---|---|---|---|---|---|---|
| Carboline Carboguard 891 FC | ||||||
| Volume Solids: | 75 ± 2% | |||||
| Theoretical Coverage Rate: | 5,0 m²/l at 150 µm | |||||
| Allow for loss in mixing and application | ||||||
| Dry Film Thickness: | 75 - 250 microns (2.95 - 9.84 mils) per coat | |||||
| Normally 150 microns | ||||||
| Dry Temperature Resistance: | Continuous: 120°C (248°F) | |||||
| Non-Continuous: 150°C (302°F) | ||||||
| Topcoat: |
Normally not topcoated May be topcoated with epoxy, polyurethane or others as recommended by Carboline |
|||||
| Limitations: | Not recommended for immersion service or exposures in areas where chalking is undesirable. | |||||
| Shelf Life: | 36 months at 24°C | |||||
| Storage Temperature and Humidity: | 5°C - 45°C | |||||
| 0-95% Relative Humidity | ||||||
| Curing Schedule | ||||
|---|---|---|---|---|
| Surface Temp | Dry to Recoat | |||
| 5°C (41°F) | 16 Hours | |||
| 10°C (50°F) | 8 Hours | |||
| 16°C (61°F) | 5 Hours | |||
| 24°C (75°F) | 3 Hours | |||
| 32°C (90°F) | 1.5 Hours | |||
General
Steel
Concrete
| Product Information | |||||
|---|---|---|---|---|---|
| Mixing: |
Power mix separately, then combine and power mix DO NOT MIX PARTIAL KITS. |
||||
| Thinning: | May be thinned up to 15% with Carboline Thinner 2 | ||||
| Use of thinners other than those supplied by Carboline may adversely affect product performance and void product warranty, whether expressed or implied | |||||
| Ratio: | 1:1 Ratio (A to B) | ||||
| Pot Life: | Approx. 3 hours at 24°C – longer at lower temperatures | ||||
| Airless Spray: | Pump Ratio: 30:1 (min.) | ||||
| GPM Output: 3.0 (min) | |||||
| Material Hose: 3/8” I.D. (min) | |||||
| Tip Size: 0.017”-0.021” | |||||
| Output PSI: 2100-2300 | |||||
| Filter Size: 60 mesh | |||||
| Brush and Roller (General): | Not recommended for tank lining applications except when striping welds. Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding. Avoid excessive re-brushing or re-rolling. For best results, tie-in within 10 minutes at 24°C | ||||
| Brush: | Use a medium bristle brush | ||||
| Roller: | Use a medium-nap synthetic roller cover with phenolic core | ||||
| Product Conditions | |||||
|---|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity | |
| Minimum | 10°C (50°F) | 5°C (41°F) | 5°C (41°F) | 0% | |
| Maximum | 30°C (86°F) | 50°C (122°F) | 45°C (113°F) | 85% | |
Clean Up
Safety
Ventilation
Caution
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Thinner 2 is a thinner for use in industrial coatings. More Information
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
