PPG SteelGuard 802

    372935

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Quantity
    Product not available
    This Product has been Discontinued

    Description

    PPG SteelGuard 802 is a one-component, thin-film solvent-borne intumescent coating for fire protection of circular and rectangular hollow section structural steel. Fast-drying for providing short handling times and can be applied on or offsite.

    Please note: This product is subject to a minimum order quantity of 440L and has an approximate delivery lead time of 21-28 days.



    Top Features & Benefits


    • Unique formulation for protection of hollow sections
    • Provides up to 90 minutes protection from cellulosic fires
    • Up to 1000 µm (40.0 mils) DFT in a single coat
    • Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is required
    • Weather resistant up to 12 months without topcoat provided the coating has been applied in accordance with INFORMATION SHEET 1222 and is not subject to running or pooling water, high humidity or immersion conditions
    • Tested and assessed to EN 13381-8
    • CE marked product, ETA 15/0053
    • Assessed to ETAG 018-2 for all durability classifications



    Product Data


    Recommended Substrate Conditions and Temperatures

    • Substrate temperature during application and curing should be between 5°C (41°F) and 40°C (104°F)
    • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
    • Ambient temperature during application and curing should be between 5°C (41°F) and 40°C (104°F)
    • Relative humidity during application and curing should not exceed 85%
    • Approved primer must be sound, dry and free from any contamination

     

     

    Instructions for Use

    • Stir thoroughly until homogeneous and free of lumps
    • Adding too much thinner results in reduced sag resistance and slower cure

     

    Airless Spray

    Recommended thinner: PPG Thinner 21-06 (normally no thinner required)

    Volume of thinner: 0 - 5%

    Nozzle angle: 20° – 50°, depending on shape of steel parts

    Nozzle orifice: Approx. 0.48 – 0.64 mm (0.019 – 0.025 in)

    Nozzle pressure: 20.0 MPa (approx. 200 bar; 2901 p.s.i.)

     

    Notes: All filters, including surge bottle and gun filters to be removed. External fluid uptake pipe filter is recommended

     

    Brush/Roller

    For small areas only (touch up and repair). No thinner should be added

     

    Cleaning Solvent

    PPG Thinner 21-06



    Data for Product
    Number of componentsOne
    Mass density1.34 kg/l (11.18 lb/US gal)
    Volume solids75 ± 3%
    VOC (Supplied)Directive 1999/13/EC, SED: max. 255.0 g/kg UK PG 6/23(92) Appendix 3: max. 327.0 g/l (approx. 2.7 lb/US gal)
    Reccomended dry film thickness200 - 1000 µm (8.0 - 40.0 mils) per coat
    Theoretical spreading rate1.07 m²/l for 700 µm (43 ft²/US gal for 28.0 mils)
    Dry to touch20 minutes
    Overcoating intervalMinimum: 4 hours
    Maximum: Unlimited
    Shelf lifeAt least 18 months when stored cool and dry



    Spreading rate and film thickness
    DFTTheoretical spreading rate
    200 µm (8.0 mils)3.75 m²/l (150 ft²/US gal)
    400 µm (16.0 mils)1.88 m²/l (75 ft²/US gal)
    500 µm (20.0 mils)1.50 m²/l (60 ft²/US gal)
    700 µm (28.0 mils)1.07 m²/l (43 ft²/US gal)
    1000 µm (40.0 mils)0.75 m²/l (30 ft²/US gal)



    Overcoating interval for DFT up to 700 µm (28 mils)
    Overcoating with...Interval5°C (41°F)10°C (50°F)15°C (59°F)20°C (68°F)30°C (86°F)
    ItselfMinimum
    Maximum
    10 hours
    Unlimited
    8 hours
    Unlimited
    6 hours
    Unlimited
    4 hours
    Unlimited
    3 hours
    Unlimited



    Overcoating interval for DFT up to 1000 µm (40 mils)
    Overcoating with...Interval5°C (41°F)10°C (50°F)15°C (59°F)20°C (68°F)30°C (86°F)
    Steelguard 2458Minimum
    Maximum
    2 hours
    Unlimited
    1.5 hours
    Unlimited
    1 hour
    Unlimited
    30 minutes
    Unlimited
    20 minutes
    Unlimited
    Other approved coatsMinimum
    Maximum
    3 days
    Unlimited
    60 hours
    Unlimited
    48 hours
    Unlimited
    24 hours
    Unlimited
    16 hours
    Unlimited



    Curing time for DFT up to 25 µm (1.0 mils)
    Substrate Temp.Dry to Touch
    5°C (41°F)1 hour
    10°C (50°F)45 minutes
    15°C (59°F)30 minutes
    20°C (68°F)20 minutes
    30°C (86°F)10 minutes





    IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.



    Product Details
    372935

    Data sheet

    Manufacturer
    PPG
    Parts
    One
    Base Type
    Solvent-borne
    Solvent
    Solvent Based
    Mixing Ratio
    -
    Suitable Substrates
    Circular and rectangular hollow section structural steel
    Key Features
    Fast-drying, on-site and off-site application, CE marked product ETA 15/0053
    Application
    Spray
    Touch Dry (at 20°C)
    20 minutes
    Dry to Handle (at 20°C)
    -
    Dry to Recoat (at 20°C)
    Up to 4 hours
    Fully Cured (at 20°C)
    -
    Pot Life (at 20°C)
    -
    Coverage
    1.07 m²/l for 700 µm (43 ft²/US gal for 28.0 mils)
    Recommended Thinner/Cleaner
    PPG Thinner 21-06
    Unit Contents
    -
    Compatible Primers
    -
    Compatible Topcoats
    Itself, PPG Steelguard 2458
    Max. Application Temperature
    40°C (104°F)
    Min. Application Temperature
    5°C (41°F)
    Density
    1.34 kg/l (11.18 lb/US gal)
    Solids by Volume
    75 ± 3%
    Heat Resistance (up-to)
    -
    VOC
    Directive 1999/13/EC, SED: max. 255.0 g/kg UK PG 6/23(92) Appendix 3: max. 327.0 g/l (approx. 2.7 lb/US gal)
    Shelf Life (Once Opened)
    At least 18 months when stored cool and dry
    UN Number
    UN1263
    Brand
    PPG
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    PPG SteelGuard 802 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    PPG Thinner 21-06

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £38.18 (ex. VAT)
    In Stock and Available for Delivery