• Rust-Oleum 3302 CombiPrimer Adhesion

Rust-Oleum 3302 CombiPrimer Adhesion


We no longer stock this product, but can recommend Rust-Oleum 3202 Galvinoleum Primer as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Product not available
This Product has been Discontinued


Rust-Oleum 3302 CombiPrimer Adhesion

Rust-Oleum 3302 CombiPrimer Adhesion is for use on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces that normal paints cannot stick to. CombiPrimer Adhesion is best brushed or sprayed onto a surface and after 30 minutes needs to be overcoated by either CombiColor Gloss or CombiColor Satin as soon as possible. This is to ensure that no dirt or dust gets trapped on the tacky surface and ensures maximum adhesion.

Product Information

  • Recommended Adhesion primer for CombiColor Gloss or CombiColor Satin
  • Ideal for galvanised steel
  • Also adheres to aluminium, PVC, stainless steel, etc.
  • To recoat after 30 minutes
  • Transparent blue appearance
  • Very high coverage: Aerosol = 4.4m² per 400ml / Brush applied = 35m² per litre


  • Density: 0,87
  • Solids content in volume: 7%
  • Heat Resistance: 100°C (dry heat)

Drying Times At 20°C/RH 50%

  • Touch dry: Remains tacky
  • Dry to handle: Remains tacky
  • Dry to recoat: After ½ hours but within 24 hours

Theoretical Consumption

35 m²/l

Practical Consumption

Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

Please note: you must recoat or apply a topcoat as soon as possible after 30 mins.

We also stock Rust-Oleum CombiPrimer Anti-Corrosion, this primer is ideal to use on steel surfaces when rust and corrosion protection is needed.

Further technical details and preparation/application instructions can be found on the product data sheet.

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.

Product Details

Data sheet

Water / Solvent Based
For Use On
Galvanised Steel, Stainless Steel, Aluminium, Copper, Glass, Porcelain
Application Method
Standard / Ready Mixed
Single, Two or Three Pack
Pack Size
400ml Aerosol, 750ml
Dry to Handle (at 20°C)
Remains tacky
Dry to Recoat (at 20°C)
After ½ hours but within 24 hours
Recommended Thinner/Cleaner
RUST-OLEUM Thinner 160
Max. Application Temperature
Min. Application Temperature
Solids by Volume
Heat Resistance (up-to)
100°C (dry heat)
741 g/l
Shelf Life (from date of manufacture)
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
Touch Dry
Remains tacky
UN Number
35 m²/l

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

questions Spencer on 2020-04-01 14:49:00

Hi I want to colour code my car bumpers using combi colour . Is this primer ok to use on them . Also is there a flexing agent I could use ?


There is not a flexing agent available of Combi colour, but you could consider Rust-Oleum CombiColor Multi-Surface as this is suitable for most plastics without a primer and is inherently flexible already.

questions sarah nicholson on 2020-03-26 16:46:01

I have some old galvanised water tanks which are rusty inside. I want to put soil in them & then plant them up. I have used a drill with wire brush to remove all the flaking dirt & rust inside but what should I paint them with please before filling them (they will have holes in the bottom) - and how long will I need to leave it to dry please. Thanks in advance


We would suggest Teamac Metaclor Antifouling Primer followed by 2 coats of Teamac Chlorvar Chlorinated Rubber Paint. Leave at least 2 weeks before filling.

questions Rory on 2020-02-18 13:01:39

Can this be applied direct to new mill finished aluminium sheeting or would you need to prepare the surface beyond cleaning and degreasing it? Thanks


Rust-Oleum 3302 CombiPrimer Adhesion should be used on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces followed by Rust-Oleum CombiColor or Rust-Oleum CombiColor Multi-Surface.

Remove grease, oil and all other surface contaminations by alkaline or high pressure cleaning in combination with appropriate detergents. Remove previous coatings completely. Remove salts, 'white rust', etc., by washing with Rust-Oleum Mathys 108 Surfa Etch Solution. The surface must be clean and dry during application.

questions chris on 2018-10-26 17:53:48

i need to re paint my 25ft aluminium boat , some areas need priming others just painting , i also require an antifowling paint for the hull any sugestions , many thanks chris


Above waterline - Remove all loose and damaged existing coating, abrade bare aluminium and spot prime immediately with Teamac QD Zinc Phosphate Primer. Undercoat primed areas with Teamac Marine Undercoat then undercoat the whole area. Finish with 2 coats of Teamac Marine Gloss.

Hull – Remove all loose and damaged existing coating and all marine growth. High pressure wash with fresh water. Do a test area with Teamac Metaclor Underwater CR Primer to ensure compatibility with existing antifoul. Abrade bare aluminium and spot prime immediately with Teamac Metaclor Underwater CR Primer then coat the whole hull with Teamac Metaclor Underwater CR Primer. Finally apply 2 coats of Teamac Antifouling A.

questions Iain on 2017-08-30 15:31:04
Question: Can this be applied directly over a new powder coated finish? I need to paint a brand new, powder coated storage shed. Thanks

Yes, followed by Rust-Oleum CombiColor.

questions BRYAN GODFREY on 2017-06-17 12:34:35
Question: Can this primer be sprayed with standard spray gun if so can it be thinned and if what with?

No, this product should be applied by brush only. It is available in an aerosol form however should you wish to spray apply.


Question about the product

* Required fields
You might also like

Rust-Oleum CombiColor Original

The ultimate direct to metal paint providing years of protection in minutes. Available in 4,400+ colours, inc. RAL, RAL Design, BS, NCS, NCS 2050 and Metallics Apply to bare, manually derusted or ready primed mild steel Primer and metal topcoat in one Interior/exterior use Sag resistant - leaves no brush/roller strokes Please note:...

Price £17.51
In Stock and Available for Delivery

Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion

Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion is a high quality anti-rust primer for Rust-Oleum CombiColor. The Anti-Corrosion Primer will ensure an even longer anti-rust protection on new or rusted steel surfaces and provides and enhances protection against corrosion. Recoatable after 2 hours For new / slightly rusted surfaces Grey for...

Price £8.68
In Stock and Available for Delivery

General Painting Application Kit

General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

Price £10.03
In Stock and Available for Delivery

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery