Thermoguard Flame Retardant Anti-Graffiti Clear Glaze is a flame-retardant clear gloss sealer and anti-graffiti coating for a variety of surfaces. It is a water-based, high durability two-pack coating, designed to enable removal of graffiti through use of graffiti removers. It can be used over existing stable and through dry paints (oil or water based) to provide a hard, abrasion resistant finish.

Also available with Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat as part of the Thermoguard Flame Retardant Anti-Graffiti BS Class 1/0 & EN Class B System. The Bonding Primer Colour Coat provides excellent adhesion & opacity. The Clear Glaze provides exceptional resistance to oils, inks, crayon, marker and spray paints

When used in conjunction with Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat, 1 coat of each combine to upgrade high-flamespread-risk “multilayer” painted walls to Class O and Class B s1 dO.

Thermoguard Flame Retardant Anti-Graffiti Clear Glaze is a High durability scrub, Flame Spread & Chemical Resistant Resin.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Colour Range & Finish
• Fire Test Standards
• Available Systems
• Surface Preparation
• Application
• Composition
• Curing
• Storage
• Coverage
• Project Fire Certificate
• Health & Safety

Features & Benefits

• Flame retardant clear gloss sealer and anti-graffiti coating for a variety of surfaces
• Fire Test Standard: BS 476 Parts 6 + 7 Class O and Class B s1 dO
• Water-based
• Can be used over existing stable and through dry paints (oil or water based) to provide a hard, abrasion resistant finish
• Also available with Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat as part of the Thermoguard Flame Retardant Anti-Graffiti BS Class 1/0 & EN Class B System
• Provides exceptional resistance to oils, inks, crayon, marker and spray paints
• Typical coverage of 40m² per 5KG Pack
• Contains high grade fade-resistant coloured pigments & adhesion promoters

Colour Range & Finish

• Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat - BS 4800 + RAL wall colours
• Thermoguard Flame Retardant Anti-Graffiti Clear Glaze - Clear finish applied over Bonding Primer Colour Coat

Fire Test Standards

BS 476 Parts 6 + 7 Class O and Class B s1 dO

To bare, painted & multi-layer painted walls:

• Over painted walls with matching or similar colour, apply – 1 coat Thermoguard Flame Retardant Anti-Graffiti Bonding Primer Colour Coat + 1 coat Flame Retardant Ant-Graffiti Clear Glaze
• Over normal porosity bare walls or contrasting colours, apply – 2 coats Thermoguard Flame Retardant Anti-Graffiti Bonding Primer Colour Coat + 1 coat Flame Retardant Ant-Graffiti Clear Glaze

Available Systems

Available as part of the Thermoguard Flame Retardant Anti-Graffiti BS Class 1/0 & EN Class B System.

Surface Preparation

• Surfaces should be clean, dry & free from contamination
• New render/mortar must be through dry
• Abrade old Anti-Graffiti or other hard, smooth, impermeable paints with 120 grit abrasive to get a good key & dust off
• Ensure good ventilation and do not apply if condensation may occur

Application

• Apply by brush, roller or spray
• Air min. 10°C, surfaces min 3°C above dew point during application & drying
• Stir base and activator thoroughly, then mix, stirring to create a homogenous mix (a paint stirrer on an electric drill is recommended)
• Pot life once mixed 2 hours

Apply:

• 1 coat Thermoguard Flame Retardant Anti-Graffiti Bonding Primer Colour Coat. Note: 2 coats MUST be applied on bare surfaces or contrasting colours
• 1 coat Flame Retardant Clear Glaze

Composition

• Clear Glaze – High durability scrub, Flame Spread & Chemical Resistant Resin
• Bonding Primer Colour Coat – High grade fade-resistant coloured pigments & adhesion promoters

Both are water-based.

Curing

Colder temperatures or high humidity delay dry, cure & hardening.

Storage

• Keep away from heat, sparks and open flame
• Store in closed original container at temperatures between 5°C and 25°C
• Keep upright
• Store separated from: Oxidising material. Alkalis. Acids

Coverage

• A 5kg pack typically covers 40m² when applied in a single coat

Project Fire Certificate

• Thermoguard issue a Fire Certificate for completed projects for property managers to demonstrate Duty of Care compliance. Click here to apply.

Health & Safety

• Please refer to the Product Safety Data Sheets prior to use

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.