• Rust-Oleum 5412 Epoxy Filler

Rust-Oleum 5412 Epoxy Filler

5412.2

We no longer stock this product, but can recommend Watco Concrex Fine Filler as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Rust-Oleum 5412 Epoxy Filler is a solvent free, two component epoxy putty for repair of small cracks, air-pockets and/or blow-holes in concrete walls and floors.

  • Extremely strong: 3x stronger than concrete
  • Shrink-free
  • Easy 1:1 mixing ratio
  • Low odour
  • For indoor and outdoor use

Quantity
Product not available
Temporarily Out of Stock

Description

Rust-Oleum 5412 Epoxy Filler

Solvent free, two component epoxy putty for repair of small cracks, air-pockets and/or blow-holes in concrete walls and floors.

5412 should be used for repair of small cracks, air-pockets and/or blow-holes in concrete walls and floors and is applied with a filling knife or a trowel. Can be applied directly on horizontal and vertical areas. Very porous substrates are to be primed with RUST-OLEUM 5401 Impregnation primer. Can be recoated with 9100, 5500, 9400, Pegakote etc

  • Easy to use putty for concrete repair
  • Can be applied directly on horizontal and vertical concrete surfaces
  • Repair of small cracks, air pockets and/or blow holes
  • Low odour
  • Prime very porous substrates with the impregnation primer 5401 first

Technical Data

  • Density: 1.45
  • Solids content in volume: 100 %
  • Solids Content in weight: 100 %
  • Compressive Strength: 75 MN/m²
  • Mixing Ratio: 1 : 1 (Volume)

Drying Times At 20°C/RH 50%

  • Touch dry: 4 h (20°C), 8 h (10°C), 3 h (30°C)
  • Dry to handle: 16 h (20°C), 36 h (10°C), 12 h (30°C)
  • Dry to recoat: 16 h (20°C), 36 h (10°C), 12 h (30°C)
  • Fully cured: 7 days (20°C), 14 days (10°C), 5 days (30°C)
  • Pot Life: 30 minutes for a 1 kg. mix at 20°C

Theoretical Consumption

1.5 kg/m² per 1 mm thickness.

Practical Consumption

Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

Surface Preparation 

Remove oil, grease and all other surface contaminations by alkaline or high pressure (steam) cleaning. Remove loose and unsound concrete until a sound surface is obtained. New concrete or masonry should dry and cure for at least 30 days before applying 5412 or a coating system. The surface should be clean and dry during application.

Mix base and activator carefully with a filling knife, preferably not in the can but on a flat substrate alike a piece of hardboard. Apply a slight over-amount of the Epoxy Putty with a filling knife or trowel; after drying reshape the surface by abrading the excessive amount.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
Product Details
5412.2

Data sheet

Interior / Exterior Use
Interior and Exterior
For Use On
Concrete
Application Method
Brush, Roller, Spray, Trowel
Sheen
Flat
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
2KG
Dry to Handle (at 20°C)
16 Hours
Dry to Recoat (at 20°C)
16 Hours
Fully Cured (at 20°C)
7 Days
Coverage
1.5 kg/m² per 1 mm thickness
VOC
0 g/l
Shelf Life (from date of manufacture)
2 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
Touch Dry
4 Hours
UN Number (Activator)
UN 2735
UN Number (Base)
UN 3082
Consumption
1.5 kg/m² per 1 mm thickness.
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Rust-Oleum 5412 Epoxy Filler is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like

Rust-Oleum 5500 Solvent Free Epoxy

Rust-Oleum 5500 Solvent Free Epoxy is a high build, solvent-free epoxy floor paint for garages, warehouses, showrooms, corridors, indoor car parks, workshops etc. Optimal protection in only one or two layers. For Professional use High build coating (150 microns), very durable Suitable for frequent (chemical) cleaning Excellent resistance...

Price £170.17 (ex. VAT)
In Stock and Available for Delivery

Rust-Oleum Mathys Pegakote

Rust-Oleum Mathys Pegakote is an easy to apply, two-pack, water based, epoxy coating for interior floor and wall surfaces in garages, warehouses, showrooms, corridors, indoor car parks, workshops, etc.  Available in 4,400+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours Please note: Colours are sold in the nearest...

Price £52.23 (ex. VAT)
In Stock and Available for Delivery

Rust-Oleum 9100 High Performance Epoxy

We no longer stock this product, but can recommend Rust-Oleum 9100 High Solids Epoxy or Rust-Oleum 9100 Winter Grade Epoxy as a great alternatives.

In stock

Rust-Oleum 5401 Epoxy Impregnation Primer

Rust-Oleum 5401 Epoxy Impregnation Primer is solvent free and improves adhesion on concrete and other porous, mineral surfaces. For Professional use Primarily intended for roller and brush application Provides a good key for adhesion on porous, mineral substrates Impregnation of porous and brittle floors Can be applied on slightly damp...

Price £136.65 (ex. VAT)
In Stock and Available for Delivery

Rust-Oleum 9400 Rust-O-Thane SL

We no longer stock this product; without knowing the use of the floor, the closest alternative product we can offer is Sikafloor 3240.

In stock