Carboline Carboguard 1341 Clear

    CARB3653

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Carboguard 1341 Clear is a penetrating primer and sealer for use on concrete substrates and Carboline Pyrocrete Fireproofing products.

    • Excellent penetrating and adhesion properties
    • Recoat after just 2 hours (at 25°C)
    • Applies at temperatures down to 10°C (4°C ambient)
    • Long pot life - up to 24 hours at 25°C

    Quantity
    Product not available
    This Product is Price on Application Only

    Description

    Carboguard 1341 Clear is a fast drying, clear penetrating primer and sealer for use on concrete substrates before top-coating.

    Not recommended for immersion service in strong acids, solvents or corrosive exposures without recommended topcoat. May be topcoated with most generic types of paints.



    Click To Jump To Section:




    Features & Benefits


    • Excellent penetrating and adhesion properties
    • Recoat after just 2 hours (at 25°C)
    • Applies at temperatures down to 10°C (4°C ambient)
    • Long pot life - up to 24 hours at 25°C



    Product Specification


    Technical Data
    Carboguard 1341 Clear
    Volume Solids:28 ± 2%
    Dry Temperature Resistance:Continuous: 80°C (176°F)
    Non-continuous: 110°C (230°F)
    Theoretical Coverage Rate:5,6 m²/l at 50 µm - Allow for loss in mixing and application
    Dry Film Thickness:40 - 100 microns (1.57 - 3.94 mils) per coat. Normally 50 µm
    Wet Film Thickness:140 - 360 µm per coat, normally 180 µm
    Limitations:Not recommended for immersion service in strong acids, solvents, or corrosive exposures without recommended topcoat.
    Topcoats:May be topcoated with most generic types of paints
    Shelf Life:Max. 24 months at 24°C
    Storage Temperature and Humidity:5° - 45°C and 0 - 95% relative humidity



    Drying Times


    Curing Schedule
    Surface TempMinimum Recoat TimeMaximum Recoat Time
    5°C (41°F)24 hours48 hours
    10°C (50°F)12 hours42 hours
    15°C (59°F)6 hours36 hours
    25°C (77°F)2 hours24 hours
    30°C (86°F)2 hours18 hours



    • If max. recoating time has elapsed, moist the surface with Carboline Thinner #2. If drying time exceeds one week, a new coat of Carboline 1341 Clear should be applied before topcoating. If not, poor adhesion or intercoat splitting may occur.



    Surface Preparation


    General

    • Surface must be clean and dry. Employ adequate methods to remove dirt, dust, oil, and all other contaminants that could interfere with adhesion of the coating.

    Steel

    • Abrasive blasting to min. Sa 2½ (ISO 8501-1). Alternatively, ultra-high pressure water jetting to Nace No. 7 min. C Vis WJ-2. Max flash rust; C Vis WJ-2M.

    Concrete

    • Concrete must be cured at least 28 days at 24°C and 50% relative humidity or equivalent. Prepare surfaces in accordance with ASTM D42582.
    • Surface Cleaning of Concrete and ASTM D4259. Abrading Concrete.
    • Voids in concrete may require surfacing.



    Application Methods


    Product Information
    Mixing:Power mix separately, then add part B to part A and power mix. DO NOT MIX PARTIAL KITS
    Ratio:2:1 (A to B) by volume
    Thinning:May be thinned up to 15% with Carboline Thinner #15
    Pot Life:24 hours at 25°C and longer at lower temperatures.
    Spray Application (General):Contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected] for information on spray equipment and technique.
    Airless Spray:Pump ratio: 30:1 (min)
    GMP Output: 2.0 (min)
    Material Hose: 3/8" I.D. (min)
    Tip Size: .013-.015”
    Output PSI: 2000
    Filter Size: 60 mesh
    Brush and Roller (General):For small areas and stripe coating. Multiple coats may be required to obtain desired appearance and recommended dry film thickness.
    Brush:Use a medium bristle brush
    Roller:Use a medium nap phenolic core roller



    Application Conditions


    Product Conditions
    ConditionMaterialSurfaceAmbientHumidity
    Minimum10°C (50°F)10°C (50°F)4°C (39°F)0%
    Maximum30°C (86°F)65°C (149°F)50°C (122°F)85%



    • Industry standards are for substrate temperatures to be 3°C above the dew point.
    • Condensation due to substrate temperatures below the dew point can interfere with proper adhesion to the substrate.
    • Special application techniques may be required above or below normal application conditions.



    Health and Safety


    Clean Up

    • Use Carboline Thinner #2 or Acetone
    • In case of spillage, absorb and dispose of in accordance with local applicable regulations.

    Safety

    • Read and follow all caution statements on this product data sheet and on the MSDS for this product.
    • Employ normal workmanlike safety precautions.
    • Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands, and all exposed areas.

    Ventilation

    • When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
    • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used.

    Caution

    • This product contains flammable solvents
    • Keep away from sparks and open flames
    • All electrical equipment and installations should be made and grounded in accordance with applicable regulations.
    • In areas where explosion hazards exist, workmen should be required to use nonferrous tools and wear conductive and non-sparking shoes.
    • Refer to the product and safety data sheets in the attachments section above for further details.
    Product Details
    CARB3653

    Data sheet

    Manufacturer
    Carboline
    For Use By
    Consumer Use
    For Use On
    Concrete
    Application Method
    Brush, Roller, Spray
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    20L
    Mixing Ratio
    2:1 (A to B) by volume
    Coverage
    5,6 m²/l at 50 µm
    Recommended Thinner/Cleaner
    Carboline Thinner #2
    Compatible Topcoats
    May be topcoated with most generic types of paints.
    Max. Application Temperature
    30°C (86°F)
    Min. Application Temperature
    10°C (50°F)
    Solids by Volume
    28 ± 2%
    Shelf Life (from date of manufacture)
    Max. 24 months at 24°C
    Recommended Dry Film Thickness
    40 - 100 microns (1.57 - 3.94 mils) per coat. Normally 50 µm
    Recommended Wet Film Thickness
    140 - 360 µm per coat, normally 180 µm
    UN Number
    UN3082
    Colour(s)
    Clear
    Base Type
    Solvent-Based
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    Carboline Carboguard 1341 Clear is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    Carboline Thinner 15

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    In stock

    Carboline Thinner 2

    Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info

    Price £32.63 (ex. VAT)
    In Stock and Available for Delivery