- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
Highly polymer modified high performance cement based waterproofing levelling base coat which has excellent workability and finishing time properties, the No1 all round product for multiple substrates. This product can be applied by hand or spray in low temperatures and used as a base coat ready to receive a suitable finish coating.
- Long Term Protection & Low Maintenance - High Adhesion
- Suitable for Hand or Spray Application - Water Repellent
- Approx. 1.5m² per bag coverage at 10mm thickness
Wethertex X71 Polymer Levelling Base Coat is a highly polymer modified high performance cement based waterproofing levelling base coat which has excellent workability and finishing time properties, the No1 all round product for multiple substrates. This product can be applied by hand or spray in low temperatures and used as a base coat ready to receive a suitable finish coating.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Technical Data
- Preparation
- Priming
- Mixing
- Application
- Storage
- Tool Equipment
- Important Information
Features & Benefits
- Long Term Protection & Low Maintenance
- High Adhesion
- Suitable for Hand or Spray Application
- Water Repellent
- Highly polymer modified high performance cement based waterproofing levelling base coat
- Excellent workability and finishing time properties
- The No1 all round product for multiple substrates
- Used as a base coat ready to receive a suitable finish coating
- Applies between 3℃ - 25℃
Technical Data
- Pack Size: 25kg Bag
- Application Tool: Sponge Float, Brush or Spray
- Suitable Substrates: Concrete, Clay, Lightweight Block, Brick, Dash and Roughcast Render
- Coverage: Approximately 1.5m2 per bag @ 10mm thick
- Water Demand:
- Levelling Coat Approx. 4.5 litres per 25kg bag
- Slurry Coat Approx. 7 litres per 25kg bag
- Ready to Finish: 2 - 8 hours @ 3°C - 25°C
- Application Temperature: 3˚C - 25˚C
- Humidity: Less than 95%
Preparation
All surfaces must be sound, clean, dry and free of any material which may impair adhesion.
Do not apply to shiny surfaces. Scaffolding must be independently tied to allow for uninterrupted application. Any faults in the structure, particularly those which may lead to moisture penetration, must be rectified. Mask around the areas where material is to be applied.
Masking tape must be removed before the material has dried out. Beads and expansion joints should be included as required by the substrate and British Standards and carried through all applied materials. Specifications for mixed or unusual substrates are available on request from our technical team on 0113 2455450 (option 2) or send a message to [email protected].
Priming
Wet down dry substrates with clean water.
Mixing
X71 Polymer Levelling Base Coat should be mixed with clean water at a rate of approximately 4.5 litres per 25kg bag using a suitable paddle or pan mixer, mix for 2 minutes, allow to stand for 2 minutes then re-mix. This process allows the additives to dissolve and activate.
Application
To avoid dampness and discolouration rendering should be avoided below DPC or within 150mm of ground level. X71 Polymer Levelling Base Coat should be applied in a one-coat 2-pass operation to a thickness of 10-15mm.
10mm Flat Finish – Ready to receive a coating The 1st pass should be applied to the primed substrate with a stainless steel trowel or spray pump, and for ease of application a serrated feather edge and finishing spatula will help. Apply the 1st pass to approx 5mm thick with fibre-reinforcing mesh included in the 1st pass ensuring that the mesh is overlapped 100mm at the mesh joints. Additional fibre-reinforcing mesh stress patches of 500 x 500 mm should be added at all openings i.e. windows and doors, and also window reveals for additional substrate stress protection. The 2nd pass should then be applied to approx. 5mm thick wet on wet to the 1st pass, levelled flat and should be left to pick up for 2-8 hours and then be wet sponge float finished flat and allowed to set. Total thickness = 10mm.
15mm Flat Finish – Ready to receive masonry paint The 1st pass should be applied to the primed substrate with a stainless steel trowel or spray pump, and for ease of application a serrated feather edge and finishing spatula will help. Apply the 1st pass to approx. 8mm thick with fibre-reinforcing mesh included in the 1st pass ensuring that the mesh is overlapped 100mm at the mesh joints. Additional fibre-reinforcing mesh stress patches of 500 x 500 mm should be added at all openings: i.e., windows and doors, and also window reveals for additional substrate stress protection. The 2nd pass should then be applied to approx. 7mm thick wet on wet to the 1st pass, levelled flat and should be left to pick up for 2-8 hours and then be wet sponge float finished flat and allowed to set. Total thickness = 15mm.
Specification Clauses relating to this product can be found in NBS Section M20 Rendering. BS 5262 Code of Practice for External Rendering and BS 8000-10 must be followed.
Note: X71 Polymer Levelling Base Coat may stiffen on standing. Re-mix the product to regain a workable consistency but do not add any more water.
Storage
When stored unopened in a dry place at temperatures above 5ºC, shelf life is 12 months from the date of manufacture.
Tool Equipment
All equipment must be washed with clean water immediately after use. Waste material should not be emptied in the drainage systems.
Important Information
The weather conditions for application and drying are critical. Do not apply if any of the following conditions are likely to arise during - or in the first 24 hours following application:
- If frost is forecast, or in excessive wet conditions
- Relative Humidity is above 95%
- In temperatures below +3ºC or above +25ºC
- If the elevation is in direct sunlight
- If the substrate is hot (at above 30ºC) or below +3ºC
- Coverage rates are approximate and do not take into account wastage and uneven substrates
The product must be protected against heavy rain, direct sun or wind in the first 24 hours after application. Sheeting the façade or the scaffold is advised to protect against this. For this particular product if these parameters are not met polymer film damage, wash off, discolouration and potential failure can occur. It is the responsibility of the application contractor to manage and record the weather conditions during application and curing of the product.
If the above is not followed or alternative products are used, then system failure may occur.
Refer any concerns to our technical team on 0113 2455450 (option 2) or send a message to [email protected].
Data sheet
- Manufacturer
- Wethertex
- Interior / Exterior Use
- Exterior Use
- For Use On
- Concrete
Clay
Blockwork
Brick
Pebbledash
Render - Application Method
- Sponge
Float
Brush
Spray - Single, Two or Three Pack
- Single
- Pack Size
- 25kg
- Coverage
- Approx. 1.5m² per bag @ 10mm thick
- Min. Application Temperature
- 3°C
- Colour(s)
- Standard Colours
- Base Type
- Cement-Based
- Suitable For Use On
- Blockwork
- Suitable For Use On
- Pebbledash
- Suitable For Use On
- Concrete
- Suitable For Use On
- Render
- Suitable For Use On
- Clay
- Suitable For Use On
- Brick
- Application Method
- Spray
- Application Method
- Float
- Application Method
- Brush
- Application Method
- Sponge
- Manufacturer
- Wethertex
- Usages
- Levelling
- Usages
- Water Resistant Coat
- Product Usage Type
- Basecoat
- Colour Family
- Grey
Nigel Rose on 2023-05-12 07:59:38 | Question: Hi, what primer do you recommend applying for this product please? Also can this be applied to a painted wall ( paint has good adhesion and is not flaking) |
Answer from Rawlins’ Technical Team: X71 is a levelling basecoat. We would advise that if this is being applied over paint as a basecoat, that reinforcing mesh is applied into the basecoat and thin fixed with insulation fixing back to the substrate. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Wethertex X71 Polymer Levelling Base Coat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT