

Sol-silicate based primer and thinner for KEIM Design-Lasur. Used as pre-treatment for strongly absorbing substrates and as dilution for most transparent finishes with KEIM Design-Lasur.
Sol-silicate based primer and thinner for KEIM Design-Lasur. Used as pre-treatment for strongly absorbing substrates and as dilution for most transparent finishes with KEIM Design-Lasur. For interior and exterior use. Especially recommended for very translucent designs and for finishes in full-tone colour shades.
With two or three Lasur coatings of KEIM Design-Lasur and KEIM Design-Fixativ highly translucent designs, especially when using full colour shades, can be achieved. The application of only one colour shade but in different dilution ratios also provides very decorative effects.
KEIM Design-Fixativ is particularly recommended as dilution for very translucent designs and for designs with full colour shades. Keep stirring the Lasur mix well before and during work. Water or other products must not be added. The Lasur is applied cross-wise with a Lasur brush (e.g. the oval KEIM Lasur brush). It is important to work swiftly weton-wet and to keep a wet edge.
Note
The components of the Design-Lasur-System KEIM DesignLasur, KEIM Design-Base and KEIM Design-Fixativ can be mixed together in any desired ratio. KEIM Design-Base provides an attractive transparency together with ideal application consistency and film thickness. KEIM DesignFixativ allows most translucent low-pigment finishes with brilliant colours and thin film thickness.
Application Conditions
Air and substrate temperature:>5°C up to max. 30°C. Apply only to dry surfaces and in dry weather. Do not apply under direct sun or on sun-heated substrates or in strong wind. Surfaces have to be protected after application from rain, wind and direct sun.
Drying Times
Between the individual coatings a drying time of about 24 hours is required.
Consumption
Depending on the dilution ratio and per coat: Approx. 50 ml/m² prepared mix of Design-Lasur and Design-Fixativ. The consumption value given is a guide value depending on the desired translucency effect, application method and substrate condition. Exact values may only be given by a trial application on site.
Clean tools with water immediately after use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.