From the Flamebar product range, Bollom Flamebar N5 is a specially formulated, effective economical water based flame retardant solution designed to improve safety. Recommended Uses Cardboard Pulpboard Hardwood Straw wall boards Plywood Stage props *Please note that the 1Ltr trigger spray size has been discontinued.
Bollom Flamebar S1WA2
From the Flamebar product range, Bollom Flamebar S1WA2 is a specially formulated, effective economical water-based flame retardant solution designed to improve safety on portable, natural materials.
- Cotton fabric
- Paper packing
- Stage drapes
*Please note that the 5Ltr size option is temporarily out of stock with the manufacturer.
Bollom Flamebar S1WA2
From the Flamebar product range, Bollom Flamebar S1WA2 is a specially formulated, effective economical water-based flame retardant solution designed to improve safety on a wide range of interior, portable lightweight absorbent natural materials.
We recommend that a small sample is tested before application to main substrate, to check suitability and application rate. Dry and test with match or suitable flame. Correctly treated items should exhibit good flame retardancy with no smouldering or after glow.
Flamebar solutions are supplied ready for use.
In a warm ventilated atmosphere drying will be quicker, but be aware that drying too quickly can cause white marking on surface. A cool iron may be used.
Will withstand dry cleaning solvents but needs re-application after washing or other exposure to water. It is long lasting in dry conditions.
It is not possible to produce a non ignitable finish on all materials. The level varies, but the most effective treatments are on absorbent materials like cotton and other natural fibres; wood, straw, cardboard and paper products etc. Synthetic materials are more difficult to treat with most plastics being extremely difficult to upgrade this way. Finishes like scotchguard stain proofing present difficulties of penetration. The purpose is to obtain the best flame retardancy possible with the particular material applying the most suitable flame retadant this is to make the material more difficult to ignite, to slow any flame spread down to a minimum and prevent smouldering. In this way, in case of fire, it helps along with other measures to provide a time delay for people to evacuate the area safely. It is the responsibility of the end user to validate the product is fit for their application.
Health and Safety
Refer to Health and Safety Sheet before use.
Apply by spraying or dipping. Test samples first for suitability and level of treatment. Check appearance when dry and fire retardancy with a flame. Normally solutions are used as supplied but in certain cases may need to be diluted.
Use trigger spray, garden type pump up sprayer or airless spray. Spray uniformly from about 30-40cm on clean, dry material. One treatment may be sufficient but repeat after drying if required. Excess may cause some stiffening. Two light sprayings are preferable to one heavy application. Adopt instructions for application to wood and paper products, boards, wall coverings and foam. Wash all equipment after use with clean water.
Use plastic or stainless steel container. Ascertain concentration required by test. Soak clean material in solution until wet out (1-2 minutes). Wring out evenly, preferably through hand or power wringer leaving in about 75% of the original weight of fabric. Dry, avoiding excess localised heat, a cool iron may be used, do not dip velvet or pile fabrics (must be sprayed).
Coverage (For all Flamebar range)
|Heavy weight / medium wt. fabric||4 - 6m² per litre|
|Light weight fabric||7 - 9m² per litre|
|Wood products||4 - 6m² per litre|
|Paper / thin card||10m² per litre|
Performance: Correctly treated items exhibit good flame retardancy with no smouldering or afterglow, but some items like synthetics which are non absorbent are more difficult to treat. The treatment is long lasting in dry conditions. It withstands dry cleaning but reapply after washing. Good fast colours are normally not affected. Protect mirrors, metals, decorative and polished surfaces. Wash with clean water.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
|Rachel on 2015-08-21 11:25:39|| |
How many square metres would 5L cover?
20-50m² per 5lt depending on the absorbency and thickness of the material it is applied to. See the Bollom Flamebar Brochure PDF which can be found under the Datasheets tab.
From the Flamebar product range, Bollom Flamebar PE6 is a specially formulated, effective economical water-based flame retardant solution designed to improve interior safety. Recommended Uses Polyester Nylon Cotton Linen Acrylic Curtains Drapes
From the Flamebar product range, Bollom Flamebar S3 is a specially formulated, effective economical water-based flame retardant solution designed to improve safety on a range of portable absorbent textiles. Recommended Uses Cotton Linen Wool Paper Cardboard Belting Welding screens