From the Flamebar product range, Bollom Flamebar N5 is a specially formulated, effective economical water based flame retardant solution designed to improve safety. Recommended Uses Cardboard Pulpboard Hardwood Straw wall boards Plywood Stage props *Please note that the 1Ltr trigger spray size has been discontinued. Shipping...
Bollom Flamebar PE6
From the Flamebar product range, Bollom Flamebar PE6 is a specially formulated, effective economical water-based flame retardant solution designed to improve interior safety.
Shipping Options (Select at Checkout):
Bollom Flamebar PE6
From the Flamebar product range, Bollom Flamebar PE6 is a specially formulated, effective economical water based flame retardant solution designed to improve safety on a wide range of interior, portable synthetic and natural materials.
- Acrylic fabrics and blends
- Dried plants / leaves
We recommend that a small sample is tested before application to main substrate, to check suitability and application rate. Dry and test with match or suitable flame. Correctly treated items should exhibit good flame retardancy with no smouldering or after glow.
Flamebar solutions are supplied ready for use.
In a warm ventilated atmosphere drying will be quicker, but be aware that drying too quickly can cause white marking on surface. A cool iron may be used.
Will withstand dry cleaning solvents but needs re-application after washing or other exposure to water. It is long lasting in dry conditions.
It is not possible to produce a non ignitable finish on all materials. The level varies, but the most effective treatments are on absorbent materials like cotton and other natural fibres; wood, straw, cardboard and paper products etc. Synthetic materials are more difficult to treat with most plastics being extremely difficult to upgrade this way. Finishes like scotchguard stain proofing present difficulties of penetration. The purpose is to obtain the best flame retardancy possible with the particular material applying the most suitable flame retadant this is to make the material more difficult to ignite, to slow any flame spread down to a minimum and prevent smouldering. In this way, in case of fire, it helps along with other measures to provide a time delay for people to evacuate the area safely. It is the responsibility of the end user to validate the product is fit for their application.
Health and Safety
Refer to Health and Safety Sheet before use.
Apply by spraying or dipping. Test samples first for suitability and level of treatment. Check appearance when dry and fire retardancy with a flame. Normally solutions are used as supplied but in certain cases may need to be diluted.
Use trigger spray, garden type pump up sprayer or airless spray. Spray uniformly from about 30-40cm on clean, dry material. One treatment may be sufficient but repeat after drying if required. Excess may cause some stiffening. Two light sprayings are preferable to one heavy application. Adopt instructions for application to wood and paper products, boards, wall coverings and foam. Wash all equipment after use with clean water.
Use plastic or stainless steel container. Ascertain concentration required by test. Soak clean material in solution until wet out (1-2 minutes). Wring out evenly, preferably through hand or power wringer leaving in about 75% of the original weight of fabric. Dry, avoiding excess localised heat, a cool iron may be used, do not dip velvet or pile fabrics (must be sprayed).
Coverage (For all Flamebar range)
|Heavy weight / medium wt. fabric||4 - 6m² per litre|
|Light weight fabric||7 - 9m² per litre|
|Wood products||4 - 6m² per litre|
|Paper / thin card||10m² per litre|
Performance: Correctly treated items exhibit good flame retardancy with no smouldering or afterglow, but some items like synthetics which are non absorbent are more difficult to treat. The treatment is long lasting in dry conditions. It withstands dry cleaning but reapply after washing. Good fast colours are normally not affected. Protect mirrors, metals, decorative and polished surfaces. Wash with clean water.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
|Charlotte on 2019-08-29 12:26:39|| |
Is this product ok to go on paper which has been coloured? I want to make sure that some crate paper flowers which have been dyed will not run when I spray this on?
It depends if the dyed colours in the paper are water soluble, this is quite likely. PE6 is a water based solution and could re-dissolve the dyes in the paper.
|Lisa on 2019-05-27 14:21:25|| |
Hi I am opening a bar/kitchen and will be required to FR my curtains, sofa etc. Can you please confirm if this liquid is suitable for hospitality premises. Thanks Lisa
You would need to seek guidance from whichever authority you need to satisfy as to what level of fire protection they require on these items. We can then help advise on which product would be best suited to achieve this.
|NIna on 2019-04-25 18:25:15|| |
I want to get something like this to cover Nylon and make it as fire retardant as possible. But I want to cover a parachute that is 26feet in diameter (!). What's the coverage of this bottle? recommended 2x coats.
This product would give a coverage of 4-9m² per litre/per coat. Based on 26 feet in diameter this would eqaute to roughly one side of the parachute being 50m² of surface area. So, this would require anywhere between 5.6-12.5 litres to apply 1 coat to 1 side.
From the Flamebar product range, Bollom Flamebar S1WA2 is a specially formulated, effective economical water-based flame retardant solution designed to improve safety on portable, natural materials. Recommended Uses Cotton fabric Silk Guaze Wool Paper packing Stage drapes *Please note that the 5Ltr size option is temporarily out...
From the Flamebar product range, Bollom Flamebar S3 is a specially formulated, effective economical water-based flame retardant solution designed to improve safety on a range of portable absorbent textiles. Recommended Uses Cotton Linen Wool Paper Cardboard Belting Welding screens Shipping Options (Select at Checkout):...