Envirograf Stoveseal
  • Envirograf Stoveseal

Envirograf Stoveseal

Product 115

Stoveseal, a finely-ground putty for patching and repairing fire-bricks, fireplaces, solid fuel ovens, ranges, boilers and around register plates, remaining flexible until cured. Stoveseal fire sealant provides a high temperature, rigid fire resistant seal around pipework and flues in fireplaces, boilers, solid fuel burners and central heating systems.

  • Ready to use and ready mixed
  • High temperature sealant
  • Bonds and seals a wide range of materials
  • For general fire protection
  • Flue pipe protection sleeves also available
  • Click to jump down to Order References

Item
£7.33
VAT excluded

£8.80 Tax incl.
Quantity

Description

Patch and repair fire-bricks, fireplaces, solid fuel ovens, ranges, boilers and around register plates using Envirograf Stoveseal, a ready-mixed, ready-to-use, finely-ground putty substance that remains flexible until cured. Stoveseal fire sealant provides a high temperature rigid seal around pipework and flues in fireplaces, boilers, solid fuel burners and central heating systems, for general fire protection.

Use the fireproof sealant to bond and seal a wide range of materials such as:

  • Metal
  • Glass
  • Ceramic
  • Concrete
  • Stone
  • Clay
  • Silicate (glass) fibre

Important - Stoveseal will not bond plastics materials, particularly where flexing may occur. Not to be used in permanent contact with water.



Ordering References


Stoveseal

Ref Size
Stoveseal/Black 310ml Tube

FL Protection Sleeve - for flue pipes

Ref Internal Size External Size Length
FL165/15/150 165mm 50mm wider 150mm
FL205/15/150 205mm 50mm wider 150mm
FL305/15/150 305mm 50mm wider 150mm
FL165/2/200 165mm 50mm wider 150mm
FL205/2/200 205mm 50mm wider 150mm
FL305/2/200 305mm 50mm wider 150mm

Application:

For maximum adhesion, remove all dirt, dust and rust and ensure that the area of application is clean.

Cut off the cartridge seal and screw nozzle onto cartridge. Cut the nozzle to the required bead size. Apply the adhesive from the cartridge, forcing it onto the area to be sealed, then immediately tool it down to ensure good adhesion. Complete tooling within 5-10 minutes.

When bonding materials, apply a bead of adhesive to one surface and immediately combine the two parts, applying pressure to ensure good surface contact.

Application equipment should be cleaned with warm water after use.

It is necessary to fully dry the product before subjecting to temperatures above 100°C to prevent gassing and likely failure or the seal/bond. Allow to air dry for 36-48 hours, after which gentle heat can be applied.

The dried product can be removed with boiling water.

Technical details:

  • Density: 1.75-1.85g/cm3
  • Flash Point: does not support combustion
  • pH: 13
  • Application Temperature Range: 5°C to 40°C
  • Service Temperature Range: -20°C to 1250°C (starts to soften at 1200°C; melts at 1300°C)
  • Slump Resistance: Excellent. Soft highly thixotropic paste.
  • Initial Drying: Skins within 5 minutes (20°C and 65% RH)
  • Through drying: Approx. 5mm/day (20°C and 65% RH)
  • Oxidation resistance: Excellent
  • Acid Resistance: Excellent (except for hydrofluoric acid)
  • Colour: natural (buff) other colours available on request.
  • Coverage: 45m for a 3mm diameter bead for a 310ml cartridge

For more information about this product's details, Test Data and Test Results included in manufacturer attachments, please contact our Technical Support team on 0113 245 5450, or send us a message here.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

Any Envirograf products to be used in or for Harrods department store should be authorised with our Technical Team prior to purchase.

Product Details
Product 115
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send