Thermoguard Flame Retardant Floor Paint

Reference:

Manufacturer:

Thermoguard Flame Retardant Floor Paint is a heavy-duty, flame retardant coating for interior concrete floors to showrooms, factories, warehouses, workshops, garages, etc. It is a water-based, high durability two-pack epoxy resin coating, designed to withstand vehicular and fork lift truck traffic. The chemically cured coating provides excellent resistance to oils, inks and other chemicals.

Bulk Buy

£125.00 tax excl.

£150.00   tax incl.
Available colours:

Product Description

Thermoguard Flame Retardant Floor Paint is a heavy-duty decorative flame retardant coating for interior concrete floors to showrooms, factories, warehouses, workshops, garages, etc. It is a water-based, high durability two-pack epoxy resin coating, designed to withstand vehicular and fork lift truck traffic. The chemically cured coating provides excellent resistance to oils, inks and other chemicals.

Colour Range & Finish

Semi-Gloss finish in the following colours;

  • Tile Red
  • Dark Green
  • Blue
  • Light Grey
  • Mid Grey
  • White

Other RAL and BS colours can be produced to order, minimum quantities and lead times apply.

Fire Performance & Tests

  • Tests at UKAS Fire Test Laboratory indicated BS 476 Parts 6 & 7 Class O, EN Class B s1 dO
  • Thermoguard issue a Fire Certificate for materials supplied to appropriate projects.

Surface Preparation

Ensure surface is sound, clean and thoroughly dry. Remove any latence or slurry. Machine polished / power floated concrete floors should be mechanically or acid etched to provide a key. If acid is used, rinse to neutralise, & allow to dry. For previously painted floors, ensure existing paint films are sound and firmly adhering. Remove all loose, flaking and suspect films, clean them thoroughly with abrasive cleaner, rinse and allow to dry thoroughly. Hard 2 pack floor paints may need abrasion to give a key. Inferior floor paints are best removed where practical.

Application

Apply by brush, roller or airless spray. Allow new concrete to fully dry and cure. Do not apply in damp conditions when condensation may form or below 4°C. Stir base and activator thoroughly, then mix, stirring well to create a homogenous mix (use of a paint stirrer on an electric drill is recommended). Pot life once mixed 2 hours.

To Bare Unpainted Floors:
Apply TWO COATS at 8m² per kg, thin first coat 10% with water.
Apply 2nd coat 16 > 72 hrs after 1st coat*.

To Previously Painted Floors:
Apply two coats at 10m² per kg/per coat.
Apply 2nd coat 16 > 72 hrs after 1st coat*.

*Overcoat times @ 20°C. In colder temperatures or humidty extend overcoat times.

Drying & Curing Times
Touch dry: 4 hours
Hard dry (foot traffic): 8 - 12 hours
Full cure 5 - 7 days

Times stated @ 20°C. Colder temperatures and high humidity extend drying, curing, and hardening times.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Technical Data

Typical Coverage (per coat)8m² per kg
Touch Dry4 hours
ApplicationBrush, Roller, Spray
The figures stated above are approximate. Please ensure you refer to all datasheets for full application information.

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions



Be the first to ask a question about this product!

Question about the product

* Required fields
Send

The question has been correctly sent

Free delivery

On orders over
£75.00 + VAT

Low trade prices

Our best trade prices on everything!

Technical Advice

Fast FREE Technical Advice for Products & Projects

Click & collect

Order and collect from
our Leeds based trade store.
silent-exothermic unable