Envirograf HW Excel Clear is a flame-retardant varnish topcoat that is used as part of an intumescent Envirograf system for timber: Matt, satin or gloss finishes available Internal use only For use over Envirograf HW02E Clear Intumescent Coating Solvent-based varnish Apply by brush or roller
Zeroflame Aquasteel WB+ Finish
Zeroflame Aquasteel WB+ Finish is a hard-wearing flame-retardant topcoat for application over Zeroflame Aquasteel WB+ Intumescent Coating:
- Class 0 fire rated finish on bare or previously painted non-combustible surfaces
- Hard wearing, water-based acrylic eggshell or solvent-based gloss finish
- High coverage rates
- Wide colour range options (RAL, BS & NCS)
Zeroflame Aquasteeel WB+ Finish is an exceptionally hard wearing decorative finish for application over Zeroflame Aquasteel WB+ Intumescent Coating and as a Class 0 fire rated finish on bare or previously painted non-combustible surfaces.
Aquasteel WB+ Finish is available as a water based acrylic eggshell or solvent based gloss finish. Both Eggshell and Gloss finishes are available in nearly all BS, RAL and NCS colours.
Apply at a rate of 12m² per litre/per coat for Eggshell and 14m² per litre/per coat for Gloss over Zeroflame Aquasteel WB+ Intumescent Coating, one coat is normally sufficient but for dark contrasting colours two may be required.
Features and Benefits
- Easily applied by brush, roller or spray
- Hard wearing, eggshell or gloss finish
- High coverage and wide colour range
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 12m² per litre
- Touch Dry
- 4 hours
- Brush, Roller, Spray
|Fiona Murphy on 22/04/2019|| |
I am currently painting an RSJ with waterbased intumescent paint and it isincredibly glutenous ,difficult to spread and the finish is really lumpy. What could cause this please?
Intumescent paint is notoriously thick and not the most aesthetic of products to use. We would recommend the paint is kept in a warm place overnight before use and then it be mechanically stirred prior to application which should make it much more fluid and easier to use.
|Darren on 05/04/2018|| |
Is it possible to just use the eggshell finish coat over the top of a steel supporting girder previously coated in Hammerite to provide 30 min fire protection or does it specifically need the intumescent undercoat?
The intumescent basecoat (Zeroflame Aquasteel WB+) must be applied first to achieve any level of fire protection. In this instance the steels would need to be completely stripped of Hammerite would need to be completely before application of Zeroflame Aquasteel WB+ and Zeroflame Aquasteel WB+ Finish.
|Stephen on 17/03/2018|| |
I want to paint a flat metal roof (lift car )that has been graffitied would this be any good?
No, Zeroflame Aquasteel WB+ Finish is part of a fire protection system for structural steel and assuming you are not trying to achieve any level of fire protection we would instead recommend Rust-Oleum CombiColor, assuming this is the internal, underside of the metal roof and it had been previously painted before the graffiti attack. Clean graffiti off first as much as possible, you may require a stain blocking primer like Zinsser Cover Stain to be applied before the CombiColor finish if the graffiti is still visible.
|Chris Burroughs on 19/10/2017|| |
Question: Hi I am installing a log burner and the surrounding wall is finished with sand and cement, what paint would you recommend?
Please refer to our blog post Painting the Walls around a Fireplace or Multi Fuel Stove for more details.
|barbara lees on 23/01/2017|| |
Question: We are currently converting our garage and do not want plasterboard walls! the building office says if we use panelling it must be class 1 spread of flame. We would like to use mdf 9mm wall panelling sheets so what paint would you recommend to make them conform?
|aubert on 13/12/2015|| |
Is Zeroflame Aquasteel WB+ Finish suitable to paint over the render of a chimney hearth?
No it isn't, we recommend using Thermoguard Wallcoat Smoke & Flame Retardant Topcoat. This product isn't heat resistant and may discolour over time if continually subjected to high temperatures, but it is a much safer alternative to standard emulsion.
|Oliver Dew on 29/06/2015|| |
Hi there, I was wondering if you can match Zeroflame Aquasteel WB+ Finish to any RAL or Pantone colour? Two colours I'm interested in are RAL 10A01 and Pantone warm gray u.
We can mix Zeroflame Aquasteel WB+ Finish to most RAL, BS and NCS colours. We cannot produce Pantone colours but can offer the 10A01 you have asked for, this is actually in the BS 4800 colour range not RAL and is available to select as a standard colour from the options listed on the product on our website.
Bollom Flameguard Ultra Primer/Undercoat is for application prior to the use of Bollom Flameguard Ultra Topcoats on bare and previously painted non-combustible surfaces. ADVANTAGES Excellent adhesion Seals porous surfaces
Nu-Flame AG Glaze acts as the final coat to the Nu-Flame Fire Protection Coating for walls and ceilings, and may also be used to overcoat matt emulsion or masonry paint. Also specially formulated to act as an anti-graffiti coating. Advantages Fire retardant and anti graffiti Water-soluble and non toxic Easy to clean UV stable
Envirograf QVFR Premier Clear Top Coat is a specially formulated, quick drying, water based protective top coating for INTERNAL smooth hardwood and softwood surfaces: Can be applied by brush, roller or spray Available in matt, satin or gloss finishes Can be used over Envirograf QVFR Clear Fire Protection Coating Low odour Quick drying
Nu-Flame FR Colourcoat is a flame retardant finish for walls and ceilings. Tested to BS 476 part 6 & 7 and satisfies Class ‘0’ Requirements of current Building Regulations, demonstrating this water-soluble coating is safe for internal use. Advantages Perfect for walls and ceilings. RAL colour shades. Can also used as a basecoat for use prior to...
Envirograf ES/VFR Translucent Top Coat is a spirit based wood stain to apply over Envirograf ES/VFR Clear Fire Protection Coating: Suitable for internal or external use Supplied ready for use, and does not need thinning For internal use apply 1 coat at 10 – 12m² per litre For external use apply 2 coats at 10 – 12m² per litre
Thermoguard Wallcoat Smoke & Flame Retardant Topcoat is a fire-retardant paint for walls and ceilings. ADVANTAGES Works in combination with Thermoguard Wallcoat Basecoat Controls surface spread of flame and fire propagation Total smoke control Stops flaming droplets and particulates to BS EN Class B s1 d0 Huge colour options Fire...
Thermoguard Flame Retardant Floor Paint is a heavy-duty, flame retardant coating for interior concrete floors to showrooms, factories, warehouses, workshops, garages, etc. It is a water-based, high durability two-pack epoxy resin coating, designed to withstand vehicular and fork lift truck traffic. The chemically cured coating provides excellent...
Nu-Flame FR Acrylic Eggshell is a special formulation for concrete, timber and painted surfaces requiring an eggshell finish. Tested to BS 476 part 6 & 7 and satisfies Class '0' Requirements of current Building Regulations. Advantages Washable eggshell finish RAL colours 14m²/Litre coverage
Nu-Flame FR Undercoat is a gloss flame retardant undercoat paint for new and previously painted surfaces where a gloss finish is required. For use on door, skirting and other timber finishes. Tested to BS 476 part 7 and passes Class 1 surface spread of flame. Advantages Flame retardant basecoat Oil-based Gloss finish RAL colours