Jotun Steelmaster 1200WF
  • Jotun Steelmaster 1200WF

Jotun Steelmaster 1200WF

Jotun Steelmaster 1200WF is a one component waterborne acrylic thin film intumescent coating independently tested and approved for fire protection of structural steel exposed to cellulosic fire up to 180 minutes. Suitable for properly prepared carbon steel substrates.

Colour
Size
£146.11
VAT excluded

£175.33 Tax incl.
Quantity

Description

Jotun Steelmaster 1200WF is specially designed as passive fire protection for steel constructions. To be used as part of a complete system for interior environments up to C3.

Approvals and certificates

  • BS 476 part 20/21
  • ASTM E84

Additional certificates and approvals may be available on request.

Features & Benefits

  • Low thickness required
  • HAPS free, green product
  • Increases productivity
  • Ready to use, easy airless spray application
  • Quicker project completion
  • Low VOC, low environmental impact
  • Safe for multiple trades
  • Tested to BS 476 (20 and 21)

Ready to use, ease of application

Steelmaster 1200WF is applied using airless spray, roller and brush for touchup only. For the full guidance notes download the Steelmaster 1200WF application guide.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Application
Brush, Spray
Touch Dry
6 hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions JULIE ARNOLD on 18/06/2019
Question: 

How much paint will I need to purchase to cover 2 x 150x90 PFC steel beams - 3585 long?

Answer: 

In addition to the information you have provided we would also need to know;

  • Level of fire protection required (i.e. 30, 60, 90min, etc.)
  • Orientation (horizontal or vertical)
  • Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
  • Environment (internal, external, car park, chemical exposure, etc.)
  • Application on site or in shop
questions Musfiqul Azad on 01/06/2019
Question: 

Is that product certified by any third party ? if Yes, please mention the name of certification body.

Answer: 

Yes, this product has a Certifire Certificate of Approval No CF 5243.

questions BURCH on 10/03/2019
Question: 

Can this material be applied by brush.

Answer: 

Application by brush is only recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness.

questions Peter Richardson on 15/01/2019
Question: 

Hello We have exposed steel rsjs in our new extension which we have built. We wpuld lile to paint them black to tie in with other structures. We know we have to paint them with intumesant paint but would lile some advice on which one and whether it is possible to apply a top coat of black. Whether that be a ajoining product by yourselves or some other. Also as the structure is in place is it possble to brush the coats on? Many thanks Peter Richardson

Answer: 

Thank you for your enquiry, please provide us with as much of the following information as possible;

  • Level of fire protection required (i.e. 30, 60, 90min, etc.)
  • Each steel section dimension (i.e. 254x146x37 UB)
  • Quantity and length of each section (or overall meterage for each section)
  • Orientation (horizontal or vertical)
  • Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
  • Environment (internal, external, car park, chemical exposure, etc.)
  • Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

questions Colin McArdle on 30/10/2018
Question: 

Do we need training by your company before we use 60 mins intumescent paint all are painters have nvq qualified,

Answer: 

Jotun don't state a requirement for any specific training but do advise the applicator should be skilled and competent to apply the product.

  

Question about the product

* Required fields
(read)
Send
16 other products in the same category:

PPG SteelGuard 564

PPG SteelGuard 564 is a one-component, thin-film, solvent-borne intumescent coating for fire protection of structural steelwork. Steelguard 564 is fast-drying and can provide up to 120 minutes protection. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is...

Price £557.20
In stock

Sherwin-Williams Firetex M95

Sherwin-Williams Firetex M95 is an epoxy intumescent suitable for cellulosic fire protection. Firetex M95 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel. 

Price £172.41
In stock

International Interchar 212

International Interchar 212 is a high performance, high build, solvent free, two pack modified epoxy intumescent fireproofing coating designed to be used on steelwork requiring protection from cellulosic fires.

Price £630.02
In stock

International Interchar 1120

International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire resistance periods...

Price £446.58
In stock

Jotun Steelmaster 60SB

Jotun Steelmaster 60SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £195.16
In stock

Jotun Steelmaster 600WF

Jotun Steelmaster 600WF is specially designed as passive fire protection for steel constructions. Designed to protect up to 60 minutes on a wide range of I section beams and columns. Will provide 90 minutes fire duration as per BS476 part 20-21. Suitable for structural steel exposed to internal environments up to corrosivity category C3 (ISO...

Price £56.19
In stock

Nullifire S606 Solvent-Based Intumescent Coating

Nullifire S606 Solvent-Based Intumescent Coating is a single pack solvent-based intumescent coating for fire protection of both internal and external structural steelwork. S606 is very pale pink in colour. S606 provides effective structural fire protection for steelwork, from 60 minutes up to a 120 minute fire rating. Suitable for universal and hollow...

Price £177.12
In stock

Bollom Brosteel Ultra 60

Due to product development the manufacturer of this product have temporarily removed it from sale - We expect to see it return in August 2019. In the meantime we can recommend Zeroflame Aquasteel WB+ as a great alternative. Bollom Brosteel Ultra 60 is a White Intumescent Paint for structural steel members:  Provides 30 and 60 minutes’ fire...

In stock

Nullifire S708 Durable Water-Based Intumescent Basecoat

Nullifire S708 Durable Water-Based Intumescent Basecoat is a white thin film intumescent coating for the fire protection of internal and semi-exposed structural steelwork but can be fully exposed during construction. It can provide up to 60 minutes fire resistance.

Price £163.76
In stock

Sherwin-Williams Firetex FX5062

Sherwin-Williams Firetex FX5062 is a water-based TCEP free thin film intumescent coating, specifically designed for airless spray application to provide fire resistance for periods up to 90 mins on structural steel. Firetex FX5062 has been Certifire Approved.

Price £156.49
In stock

PPG SteelGuard 851

A one component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Short handling times are accomplished due to the fast-drying nature of this coating, and provides up to 120 minutes of protection from cellulosic fires. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944);...

Price £420.20
In stock

Jotun Steelmaster 120SB

Jotun Steelmaster 120SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £195.23
In stock

PPG SteelGuard 751

PPG SteelGuard 751 is a one-component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires. Top Features Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4 CE marked product, ETA 15/0439 Assessed to ETAG 018-2 for all durability...

Price £469.20
In stock

Zeroflame Aquasteel WB+

Zeroflame Aquasteel WB+ is a White Intumescent Coating that is ideal for smaller fireproofing jobs on steel. Achieves 30 and 60 mins' fire resistance on structural steel profiles Tested to internationally accepted standards BS476 Parts 20 and 21 Certificate application included Fast drying Apply by brush, roller or airless spray...

Price £50.99 Regular price £56.66
In stock